ENGINE AR 1763172 - Caterpillar

1763172 ENGINE AR Caterpillar parts 315C

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1763172
176-3172
1763172

Buy ENGINE AR 1763172 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Related part:

1763172 ENGINE AS-PRIM 10R8792 R

1763172 BLOCK GP-LONG 20R4080 R

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Overhaul Rebuild Kit For Caterpillar CAT 3054 3054C 3054E Engine Backhoe 416 426

$955.89

06 May 2022

CN: KenanKe Parts

Overhaul Rebuild Kit For Caterpillar CAT 3054 3054C 3054E Engine Backhoe 416 426
GMAOLIHAIKA Part Number: 176-3172,234-3059 176-3180,234-3061 177-9752,241-8582 178-9011,241-8584 179-1795,241-8585 188-5099,241-8586 188-5100,244-3103 194-9477,244-3105 207-1175,256-4720 213-0296,257-8359 || Application: For CAT Caterpillar 3054C/E 3054C 3054E Backhoe Loader 416E 422E 428D 428E Caterpillar excavator M313C M315C 313 315L Compact Track Loaders:PT100 || Contains the Following: 1 Set of Overhaul Gasket Kit 4 Cylinder Liners 4 Pistons STD 4 Piston Pins 8 Snap Rings 4 Rod Bushings Set Rings For 4 Pistons STD 1 Set of Main Bearings 1 Set of Rod Bearings 1 Set of Thrust Bearings 8 Valve Guide 8 Intake Valves/Exhaust Valves 8 Intake Valves Seats/Exhaust Valves Seats

Overhaul Rebuild Kit For Caterpillar CAT 3054C 3054E 3054C/E Backhoe Loader 416E 422E 428D 428E

$955.89

06 May 2022

CN: KenanKe Parts

Overhaul Rebuild Kit For Caterpillar CAT 3054C 3054E 3054C/E Backhoe Loader 416E 422E 428D 428E
GMAOLIHAIKA Part Number: 176-3172,234-3059 176-3180,234-3061 177-9752,241-8582 178-9011,241-8584 179-1795,241-8585 188-5099,241-8586 188-5100,244-3103 194-9477,244-3105 207-1175,256-4720 213-0296,257-8359 || Application: For CAT Caterpillar 3054C/E 3054C 3054E Backhoe Loader 416E 422E 428D 428E Caterpillar excavator M313C M315C 313 315L Compact Track Loaders:PT100

For full view, you need register

Compatible equipment models: 1763172:

EXCAVATOR 315C Caterpillar

Information:

Illustration 1 g00797135
Schematic of the Solenoid Valve for One-way Flow or Two-way FlowThis diagnostic is associated with the solenoid valve for one-way flow or two-way flow. This diagnostic code is recorded when the implement ECM reads the current of the solenoid as being below normal. There is an open circuit.The possible causes of this diagnostic code are listed:
The signal circuit of the solenoid is open.
The return circuit of the solenoid is open.
The solenoid has failed.
The implement ECM has failed. This is unlikely. System Response:When this diagnostic code occurs, there is no warning on the monitor. The diagnostic code will only be active when the control for the work tool is actuated. An example of this action is pressing the pedal for operating a hammer. The diagnostic code is active when the pedal is pressed. When the pedal is no longer pressed, the diagnostic code is not active, but the code is present in the diagnostic code log ("LOGGED ERROR" screen). Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code is corrected.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Disconnect the solenoid with the diagnostic code from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire K866-WH) to frame ground.
Determine if CID 1615 FMI 05 is present. Check the "ACTIVE ERROR" screen on the monitor.Expected Result:The diagnostic code is not active when the jumper wire is installed. Results:
YES - The diagnostic code is not active when the jumper wire is installed. The circuit is correct. Repair: The solenoid has failed. Repeat this test step "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Verify that the new solenoid corrects the problem.STOP
NO - The diagnostic code remains active. The jumper wire does not affect the diagnostic code. Proceed to test step 2.Test Step 2. CHECK THE HARNESS FOR AN OPEN.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the CONN189 and CONN190 machine harness connectors from the implement ECM.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire K866-WH) to contact 2 (wire 235-BK).
At the machine harness connector for the ECM, measure the resistance from signal contact CONN190-1 (wire K866-WH) to frame ground.Expected Result:The resistance should be less than 5.0 ohms.Results:
OK - The resistance is less than 5.0 ohms. The machine harness is correct. Proceed to test step 3.
NOT OK - The resistance is greater than 5.0 ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: The open is in wire (K866-WH) or in wire (235-BK) of the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors and clean the contacts of the harness connectors.
Reconnect all harness connectors.