AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1802003 - Caterpillar



1802003 ENGINE AR-COMPLETE Caterpillar parts 3406E ENGINE
Rating:
46
Alternative (cross code) number:
CA1802003
180-2003
1802003
Caterpillar 1802003 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1802003 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 1802003:

TRUCK ENGINE  3406E   Caterpillar
  For full view, you need register

Information:

Note: In order to perform this test and adjust, the brakes must be disconnected or the machine must be placed on jack stands.Note: The machine is equipped with two propel motors. The propel motors are similar. The following procedure illustrates the test on the rear propel motor. The same procedure can be used to test the front propel motor.
Drive the machine to a smooth, horizontal surface.
Illustration 1 g03243457
Move propel lever (1) to the NEUTRAL position.
Move parking brake switch (2) to the ON position.
Use throttle control switch (3) in order to operate the engine in ECO mode or in low idle. Note: Two things indicate when the engine is in ECO mode. First, "ECO" will appear on the display. Second, the second LED next to throttle control switch (3) will be illuminated. Two things indicate when the engine is at low idle. First, "Low Idle" will appear on the display. Second, the first LED next to the throttle control switch will be illuminated.
Move engine start switch (4) to the OFF position.
Illustration 2 g03243516
Apply Tool (G) on the NPT side of each Tool (A). Install one Tool (A) in each side of Tool (B).
Assemble Tool (C) and Tool (D). Connect one Tool (D) to each Tool (A) on Tool (B).
Assemble Tool (E) and Tool (F). Make two sets of this tool assembly. Connect Tool (E) from one of tool assemblies to Tool (C) on each side of the flowmeter.
Illustration 3 g03243518
Loosen clamp (6). Remove hose (5) from adapter (7). Remove the adapter from the propel motor.
Reconnect hose (5) to adapter (7). Tighten clamp (6) on the hose and the adapter.
Install Tool (H) in the propel motor.
Install Tool (E) from inlet side of Tool (B) onto Tool (H).
Install Tool (J) onto adapter (7).
Install Tool (E) from outlet side of Tool (B) onto Tool (J).
Illustration 4 g03243576
Brake hose assembly on solid drum motor.
Disconnect brake supply hose assembly (8) at the two propel motors on solid drum machines. Use Tool (R) to cap the brake inlet port in the propel motors. Use Tool (S) to plug the brake supply hose assembly.
Move engine start switch (4) to the START position. Release the switch when the engine starts.
Operate the engine at low idle for a few minutes. Use throttle control switch (3) in order to operate the engine in high idle. Note: Two things indicate when the engine is at high idle. First, "High Idle" will appear on the display. Second, all three LED's next to throttle control switch (3) will be illuminated.
Monitor the hydraulic oil temperature with Tool (K). Operate the machine until the oil temperature reaches 43 5.6 °C (110 10 °F).
Move parking brake switch (2) to the OFF position.
Illustration 5 g03243578
Use speed control buttons (9) in order to set the propel speed to 50 percent. Note: Two things indicate when the propel speed is set to 50 percent. First, "Speed Control % 50" will appear on the display. Second, four LEDs next to speed control buttons (9) will be illuminated.
Modulate propel lever (1) forward until

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.