ENGINE AR-COMPL 20R0428 - Caterpillar

D3400 - (9J4001, 1N7001, 3R6001, 3S7001, 9S4001, 1T7001); D4400 - (4H1, 4H9001, 1N4001, 3R2001, 1S1, 6S1); D4600 - (4H8001, 1N1, 3R4001, 1S5001, 5S1); D6600 - (5E9501); D7700 - (4C6501, 4H6001, 9J3001, 9J6501); D8800 - (5E5001, 4H3269, 9J2001, 9J6001, 1N8001, 2S1, 6S5001); D11000 - (4C8001, 4H7001, 9J1001, 9J8001); D13000 - (28B, 29B, 30B, 5E2001, 9J1, 9J7501, 1N1001, 1N9001, 3R7001, 3S2001, 4S1, 4S1001, 7S1, 1T1, 2V5001); D17000 - (5E9001, 9J5001, 9J8501, 3S1, 8S5001, 2V1, 8V1); D2 - (3J, 5J); D4 - (4G, 7J, 2T, 5T); D6 - (4R, 5R); D7 - (9G2876, 7M, 3T, 4T, 6T); D8 - (13A, 1H2409, 8R, 2U); NO. 10 - (1K, 2K,); DW10 - (1N2001, 6V5001); NO. 11 - (5K, 6K); NO. 48 - (5F); NO. 112 - (2M, 4M); NO. 212 - (1M, 1R, 1U)
(1) 1 -9M92682 -9M93613 -9M93624 -9M93595 -9M93606 -1D45387 -9M93318 -1A9136The above tools, part of 9M9267 Tool Group, are required for this group of engines. (2) Remove the cover from the side of the fuel pump. Remove the rack limiter, if so equipped. Fasten indicator (1) to one end of bar (2) with bolt (8). Bolt bar (2) to the fuel pump housing using spacer (5) and bolt (6). Install clamp (3) on the rack and lock it with screw (7). (3) Position the rack on the centerline of the fifth tooth by engaging the inner set of notches on gauge (4) behind the last tooth on each side of one of the fuel pump sector gears. Draw the shoulder of the gauge up over the rack. With gauge (4) in place, loosen screw (7) and slide clamp (3) along the rack until indicator (1) reads zero. Remove gauge (4) and slide the rack back and forth several times. Reinstall the gauge and check the zero reading. Repeat this procedure until a consistent zero reading is obtained. To check the rack, adjust the governor control lever so the rack stop is within .001" of the torque spring. Read the rack setting on indicator (1). If the rack setting is not correct, adjust the rack stop or torque spring according.3406 - 90U, 91U, 92U, 70V
(1) 1 -9S73502 -8S46273 -9S2154 -9S89035 -9S85196 -9S8521The above components of 9S240 Tool Group are required for this group of engines. (2) Remove stop (7), spacer (8) and gaskets (9). Disconnect the governor control linkage at the governor lever. (3) Remove the plug in the bottom of the governor housing. Install plug (5) and rod (6). Push in on rod (6) to retract the speed limiter and tighten plug (5) to hold the rod. Install bracket group (1), with