AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 2142903 - Caterpillar



2142903 ENGINE AR-COMPLETE Caterpillar parts C-12 ENGINE
Rating:
60
Alternative (cross code) number:
CA2142903
214-2903
2142903
Caterpillar 2142903 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 2142903 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 2142903:

TRUCK ENGINE  C-12   Caterpillar
  For full view, you need register

Information:


Illustration 1 g02067293
Left rear viewTypical example (1) As required, use the following shims until the centerline of front and rear roller assemblies are within 2.0 mm ( 0.08 inch) of the center line of the drive wheel. 190-2479 Shim Thickness of one shim ... 1.50 mm (0.059 inch) 190-2478 Shim Thickness of one shim ... 3.00 mm (0.118 inch) 190-2477 Shim Thickness of one shim ... 6.35 mm (0.250 inch) (2) As required, use the following shims until the centerline of front and rear roller assemblies are within 2.0 mm ( 0.08 inch) of the center line of the drive wheel. 190-2489 Shim Thickness of one shim ... 0.45 mm (0.018 inch) 190-2488 Shim Thickness of one shim ... 1.50 mm (0.059 inch) 190-2487 Shim Thickness of one shim ... 3.00 mm (0.118 inch) 190-2486 Shim Thickness of one shim ... 6.35 mm (0.250 inch) (3) Torque for the bolt ... 1350 50 N m (996 37 lb ft) (4) Torque for bolts ... 900 100 N m (664 74 lb ft) (5) Install the plate to the face of the shaft. As required, add the shims between the plate and the frame until the gap is within 0.5 mm (0.02 inch).
Illustration 2 g02067314
(6) Apply 4C-4030 Thread Lock Compound to the threads of two screws. (7) Use grease fittings in order to pack the bearings with 5P-0960 Grease Cartridge. Then replace the grease fittings with the pipe plugs. (8) Allow 6.0 2.0 mm (0.24 0.08 inch) of the rod thread to protrude past the nut. (9) Torque for the nut ... 340 50 N m (251 37 lb ft) (10) Torque for two nuts ... 237 50 N m (175 37 lb ft) (11) Before assembly, apply 4C-5599 Anti-Seize Compound to the cylindrical surface that are in contact with the pin. (12) Torque for the bolt ... 271 50 N m (200 37 lb ft) (13) Apply 5P-0960 Grease Cartridge through the grease fitting until the grease is visible on both sides of the bearing. (14) Install the lip type seals, so that the lip of the lip type seal faces outward.Note: Freeze the sleeve bearing to −65 °C (−85 °F) prior to installation. Apply 5P-0960 Grease Cartridge to the inside surfaces of the sleeve bearing. (15) 206-2615 Sleeve Bearing Inside diameter ... 50.845 0.020 mm (2.0018 0.0008 inch) Outside diameter ... 63.564 0.013 mm (2.5025 0.0005 inch) Installation depth of the sleeve bearing ... 10.5 1.0 mm (0.41 0.04 inch)

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.