AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 2155177 - Caterpillar



2155177 ENGINE AR-COMPLETE Caterpillar parts C-12 ENGINE
Rating:
23
Alternative (cross code) number:
CA2155177
215-5177
2155177
Caterpillar 2155177 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 2155177 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 2155177:

TRUCK ENGINE  C-12   Caterpillar
  For full view, you need register

Information:


Table 1
Required Tools    
Tool    Part
Number    Description    Qty    
A     4C-8689     Flow Meter Gp
1.9 to 18.9 L/min (0.5 to 5.0 US gpm)     1    
007-0950 Pipe Adapter     2    
8C-6872 Connector     2    
B     124-2117     Coupling     1    
122-6870 Hydraulic Hose
1 m (40 inch)     1    
124-2147 Coupling     1    
6V-8398 O-Ring Seal     2    
C     4C-6500     Digital Thermometer        
Drive the machine to a smooth, horizontal surface on loose, uncompacted soil.Note: If loose, uncompacted soil is unavailable, drive the machine onto an unusable tire without rims. The tires should have a carcass of substantial stiffness in order to support the drum. If tires are used, the drum should be a minimum of 102 mm (4 inch) above the ground.
Illustration 1 g02092563
Move propel lever (1) to the NEUTRAL position.
Illustration 2 g02092564
Move parking brake switch (2) to the ON position.
Illustration 3 g02092565
Move throttle control switch (3) to the LOW IDLE position.
Illustration 4 g02092566
Move engine start switch (4) to the OFF position.
Illustration 5 g02093675
Assemble Tool (A). Assemble Tool ( B). Attach Tool (A) to Tool (B), as shown.
Illustration 6 g02093676
Disconnect case drain line (5) from vibratory motor fitting (6) .
Connect case drain line (5) to the outlet port of flow meter of Tool (A). Connect inlet hose from Tool (A) to vibratory motor fitting (6) .
Move engine start switch (4) to the START position. Release the switch when the engine starts.
Operate the engine at low idle for a few minutes. Move throttle switch (3) to the HIGH IDLE position.
Monitor the hydraulic oil temperature with Tool (C). Operate the machine until the oil temperature reaches 43 6 °C (110 10 °F).
Read flow on Tool (A). The flow should be less than 3.8 L/min (1.0 US gpm).
Illustration 7 g02093674
Move amplitude selector switch (7) to the LOW AMPLITUDE position.
Illustration 8 g02093673
Depress vibratory switch (8) on top of propel lever in order to start the vibratory system.
Read the flow on the flow meter. The flow should be between 4.5 to 8.0 L/min (1.2 to 2.1 US gpm).
Depress vibratory switch (8) on top of propel lever in order to stop the vibratory system.
Move amplitude selector switch (7) to the HIGH AMPLITUDE position.
Depress vibratory switch (8) on top of propel lever in order to start the vibratory system.
Read the flow on the flow meter. The flow should be between 4.5 to 8.0 L/min (1.2 to 2.1 US gpm).
Depress vibratory switch (8) on top of propel lever in order to stop the vibratory system.
Move throttle switch (3) to the LOW IDLE position.
Move engine start switch (4) to the OFF position.
Remove Tool (A) from the vibratory motor and reconnect case drain line (5) .

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.