2387113 ENGINE AR-COMPLETE Caterpillar parts
C7
Rating:
Alternative (cross code) number:
CA2387113
238-7113
2387113
CA2387113
238-7113
2387113
TRUCK ENGINE,
Compatible equipment models: 2387113:
For full view, you need register
Information:
SMCS Code: 5068-510-RJRemove The Filter Cartridge
The return filter is a cartridge type filter. The return filter reduces the amount of foreign material that enters the hydraulic system when the filter element is replaced.
Illustration 214 If the indicator for a Restricted Hydraulic Return Filter comes on, push the reset switch at the filter case. Run the machine on level ground for approximately 10 minutes. If the indicator still comes on, inspect the filter and replace the filter, if necessary.
Illustration 2151. Loosen the filler plug in order to relieve the hydraulic tank pressure. Tighten the filler plug after the hydraulic tank pressure is relieved. The return filter is located behind the filler plug.
Illustration 216
(1) Bolts. (2) Washers. (3) Cover. (4) Plug. (5) Filter cartridge.2. Remove bolts (1), washers (2), and cover (3). Refer to Operation and Maintenance Manual, "General Hazard Information" for information on Containing Fluid Spillage.3. Remove plug (4) in order to release the pressure in filter cartridge (5).
Illustration 217
(5) Filter cartridge. (6) Filter case. (A) Guide.4. Pull up the handle at the top of filter cartridge (5) until the filter cartridge contacts guide (A) on filter case (6).
Illustration 2185. Turn the filter cartridge counterclockwise by 1/2turn in order to align the projection of the filter cartridge with the notch of the filter case. Pull out the filter cartridge.
Illustration 219
(7) O-ring.6. Inspect the cover and O-ring (7). If either part is damaged, replace the part.7. Inspect the filter cartridge for debris and for damage. If necessary, replace the filter cartridge.Remove The Filter Element
Illustration 220
(4) Plug. (8) Plate. (18) O-ring.1. Make sure that plug (4) is removed. Make sure that all of O-ring (18) is removed from plate (8).
Illustration 221
(8) Plate. (9) Spiral retaining ring.2. Use a flat screwdriver in order to remove spiral retaining ring (9).
Illustration 222
(8) Plate. (10) Shell. (11) O-ring. (12) Filter element.3. Hold the filter cartridge with one hand. Grasp the grip of plate (8) with your other hand. Lift plate (8) in order to separate plate (8) from the filter cartridge.4. Remove O-ring (11) from plate (8).5. Lift filter element (12) from shell (10).6. Pour the remaining oil into a suitable container.Clean Shell Of Filter Cartridge
Illustration 223
(13) Slide plate. (14) Blotter Pads. (15) Screws. (19) Port.1. Turn shell (10) upside-down.2. Remove screws (15).3. Remove Blotter Pads (14) from slide plate (13).4. Wash the following parts in a clean nonflammable solvent: plug (4), plate (8), spiral retaining ring (9), shell (10), and Blotter Pads (14). Dry the parts.Install The Filter Element
Use the parts found in 137 - 3635 Service Kit when installing the filter element and the filter cartridge.1. Spray oil to the inside of shell (10) in order to prevent rust.2. Apply grease to a new O-ring (11).3. Plate (8) will contact the inside of shell (10). Apply grease to this point.4. Apply grease to O-rings inside ports (19) at the bottom of shell (10).5. Install new Blotter Pads (14). Tighten the screws to a torque of 0.4 N m (3.5 lb in).6. Spray
The return filter is a cartridge type filter. The return filter reduces the amount of foreign material that enters the hydraulic system when the filter element is replaced.
Illustration 214 If the indicator for a Restricted Hydraulic Return Filter comes on, push the reset switch at the filter case. Run the machine on level ground for approximately 10 minutes. If the indicator still comes on, inspect the filter and replace the filter, if necessary.
Illustration 2151. Loosen the filler plug in order to relieve the hydraulic tank pressure. Tighten the filler plug after the hydraulic tank pressure is relieved. The return filter is located behind the filler plug.
Illustration 216
(1) Bolts. (2) Washers. (3) Cover. (4) Plug. (5) Filter cartridge.2. Remove bolts (1), washers (2), and cover (3). Refer to Operation and Maintenance Manual, "General Hazard Information" for information on Containing Fluid Spillage.3. Remove plug (4) in order to release the pressure in filter cartridge (5).
Illustration 217
(5) Filter cartridge. (6) Filter case. (A) Guide.4. Pull up the handle at the top of filter cartridge (5) until the filter cartridge contacts guide (A) on filter case (6).
Illustration 2185. Turn the filter cartridge counterclockwise by 1/2turn in order to align the projection of the filter cartridge with the notch of the filter case. Pull out the filter cartridge.
Illustration 219
(7) O-ring.6. Inspect the cover and O-ring (7). If either part is damaged, replace the part.7. Inspect the filter cartridge for debris and for damage. If necessary, replace the filter cartridge.Remove The Filter Element
Illustration 220
(4) Plug. (8) Plate. (18) O-ring.1. Make sure that plug (4) is removed. Make sure that all of O-ring (18) is removed from plate (8).
Illustration 221
(8) Plate. (9) Spiral retaining ring.2. Use a flat screwdriver in order to remove spiral retaining ring (9).
Illustration 222
(8) Plate. (10) Shell. (11) O-ring. (12) Filter element.3. Hold the filter cartridge with one hand. Grasp the grip of plate (8) with your other hand. Lift plate (8) in order to separate plate (8) from the filter cartridge.4. Remove O-ring (11) from plate (8).5. Lift filter element (12) from shell (10).6. Pour the remaining oil into a suitable container.Clean Shell Of Filter Cartridge
Illustration 223
(13) Slide plate. (14) Blotter Pads. (15) Screws. (19) Port.1. Turn shell (10) upside-down.2. Remove screws (15).3. Remove Blotter Pads (14) from slide plate (13).4. Wash the following parts in a clean nonflammable solvent: plug (4), plate (8), spiral retaining ring (9), shell (10), and Blotter Pads (14). Dry the parts.Install The Filter Element
Use the parts found in 137 - 3635 Service Kit when installing the filter element and the filter cartridge.1. Spray oil to the inside of shell (10) in order to prevent rust.2. Apply grease to a new O-ring (11).3. Plate (8) will contact the inside of shell (10). Apply grease to this point.4. Apply grease to O-rings inside ports (19) at the bottom of shell (10).5. Install new Blotter Pads (14). Tighten the screws to a torque of 0.4 N m (3.5 lb in).6. Spray
