2407750 ENGINE AR Caterpillar parts
994F
Rating:
Alternative (cross code) number:
CA2407750
240-7750
2407750
CA2407750
240-7750
2407750
Weight: 20000 pounds 9071 kg.
WHEEL LOADER,
Related part:
2407750
ENGINE AR-BASIC
10R2853
R
This part in 5 request:
Show.
This information for suppliers only!
2022-03-08
2021-12-23
2021-12-08
2018-08-27
2017-06-06
Compatible equipment models: 2407750:
For full view, you need register
Information:
TYPE="TABLE" @@@-->
Engine exhaust contains products of combustion which may be harmful to your health. Always start and operate the engine in a well ventilated area and, if in an enclosed area, vent the exhaust to the outside.
Perform the required daily maintenance and other periodic maintenance before starting the engine. Inspect the engine room. This inspection can help prevent major repairs at a later date. See this Operation and Maintenance Manual, "Maintenance Interval Schedule" (Maintenance Section).Walk-Around Inspection
For any type of leak (coolant, lube, or fuel) clean up the fluid. If leaking is observed, find the source and correct the leak. If leaking is suspected, check the fluid levels more often than recommended until the leak is found or fixed, or until the suspicion of a leak is proved to be unwarranted.
To obtain maximum service life for your engine, make a thorough inspection before starting the engine. Make a walk-around inspection of the installation. Look for items such as oil or coolant leaks, loose bolts, and trash buildup. Remove any trash. Arrange for repairs, as needed.
The guards must be in the proper place. Repair damaged guards or replace missing guards.
Ensure that the areas around the rotating parts are clear.Air Inlet System
Ensure that the air inlet piping and the air filters are in place.
Ensure that all clamps and connections are secure.
Observe the air cleaner service indicator. Service the air cleaner when the yellow diaphragm enters the red zone, or when the red piston locks in the visible position.Cooling System
Inspect the cooling system for leaks or loose connections.
Inspect the cooling system hoses for cracks and for loose clamps.
Inspect the water pumps for evidence of leaks.
Inspect the fan drive belts for cracks and for deterioration.
Check the coolant level. Add coolant, if necessary. For information on the proper coolant to use, see this Operation and Maintenance Manual, "Refill Capacities and Recommendations" (Maintenance Section).Generator
Perform any maintenance that is required for the generator. See this Operation and Maintenance Manual, "Maintenance Interval Schedule" (Maintenance Section).
Ensure that the main circuit breaker is open.Electrical System
Inspect the wiring for the following conditions:
Loose connections
Wiring that is worn or frayedInspect the alternator belt for cracks and for deterioration.Ensure that the grounds are secure.Fuel System
All valves in the fuel return line must be open before and during engine operation to help prevent high fuel pressure. High fuel pressure may cause filter housing failure or other damage.
Inspect the fuel lines for loose fittings and leaks. Ensure that the fuel lines are properly clamped.
Ensure that the fuel is supplied to the engine.If the engine has not been started for several weeks, fuel may have drained from the fuel system. Air may have entered the filter housing. Also, when fuel filters have been changed, some air space will be left in the housing. In these instances, prime the fuel system. See this Operation and Maintenance Manual, "Fuel System-Prime" (Maintenance Section) for information on priming the fuel system.Lubrication System
Illustration 1 g03843325
Oil level gauge
(1) "ADD" mark
(2) "FULL" mark
Check the engine crankcase oil level. Maintain the oil level between the
Engine exhaust contains products of combustion which may be harmful to your health. Always start and operate the engine in a well ventilated area and, if in an enclosed area, vent the exhaust to the outside.
Perform the required daily maintenance and other periodic maintenance before starting the engine. Inspect the engine room. This inspection can help prevent major repairs at a later date. See this Operation and Maintenance Manual, "Maintenance Interval Schedule" (Maintenance Section).Walk-Around Inspection
For any type of leak (coolant, lube, or fuel) clean up the fluid. If leaking is observed, find the source and correct the leak. If leaking is suspected, check the fluid levels more often than recommended until the leak is found or fixed, or until the suspicion of a leak is proved to be unwarranted.
To obtain maximum service life for your engine, make a thorough inspection before starting the engine. Make a walk-around inspection of the installation. Look for items such as oil or coolant leaks, loose bolts, and trash buildup. Remove any trash. Arrange for repairs, as needed.
The guards must be in the proper place. Repair damaged guards or replace missing guards.
Ensure that the areas around the rotating parts are clear.Air Inlet System
Ensure that the air inlet piping and the air filters are in place.
Ensure that all clamps and connections are secure.
Observe the air cleaner service indicator. Service the air cleaner when the yellow diaphragm enters the red zone, or when the red piston locks in the visible position.Cooling System
Inspect the cooling system for leaks or loose connections.
Inspect the cooling system hoses for cracks and for loose clamps.
Inspect the water pumps for evidence of leaks.
Inspect the fan drive belts for cracks and for deterioration.
Check the coolant level. Add coolant, if necessary. For information on the proper coolant to use, see this Operation and Maintenance Manual, "Refill Capacities and Recommendations" (Maintenance Section).Generator
Perform any maintenance that is required for the generator. See this Operation and Maintenance Manual, "Maintenance Interval Schedule" (Maintenance Section).
Ensure that the main circuit breaker is open.Electrical System
Inspect the wiring for the following conditions:
Loose connections
Wiring that is worn or frayedInspect the alternator belt for cracks and for deterioration.Ensure that the grounds are secure.Fuel System
All valves in the fuel return line must be open before and during engine operation to help prevent high fuel pressure. High fuel pressure may cause filter housing failure or other damage.
Inspect the fuel lines for loose fittings and leaks. Ensure that the fuel lines are properly clamped.
Ensure that the fuel is supplied to the engine.If the engine has not been started for several weeks, fuel may have drained from the fuel system. Air may have entered the filter housing. Also, when fuel filters have been changed, some air space will be left in the housing. In these instances, prime the fuel system. See this Operation and Maintenance Manual, "Fuel System-Prime" (Maintenance Section) for information on priming the fuel system.Lubrication System
Illustration 1 g03843325
Oil level gauge
(1) "ADD" mark
(2) "FULL" mark
Check the engine crankcase oil level. Maintain the oil level between the