AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 2444583 - Caterpillar


2444583 ENGINE AR-COMPLETE Caterpillar parts C-15
Rating:
16
Alternative (cross code) number:
CA2444583
244-4583
2444583
Caterpillar 2444583 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 2444583 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 2444583:

TRUCK ENGINE  C-15   Caterpillar
  For full view, you need register

Information:

Note: A temporary setting of the main relief valve is required before travel crossover relief valves can be tested. Refer to Testing and Adjusting, "Relief Valve (Main) - Test and Adjust".
Position the machine on level ground.
Stop the engine.
Illustration 1 g01428847
Pump compartment
(1) Pressure tap (delivery pressure for drive pump)
(2) Pressure tap (delivery pressure for idler pump)
(3) Pressure tap (power shift pressure)
Connect a 60000 kPa (8700 psi) pressure gauge to pressure tap (1). Use this pressure gauge to monitor the crossover relief valve pressure setting of the right travel motor.
Connect a 60000 kPa (8700 psi) pressure gauge to pressure tap (2). Use this pressure gauge to monitor the crossover relief valve pressure setting of the left travel motor.
Connect a 6000 kPa (870 psi) pressure gauge to pressure tap (3).
Illustration 2 g00714259
Sprocket (left track)
(16) Sprocket
(17) FT-2547 Blocker Pin
Place blocker pin (17) in sprocket (16) in order to block forward left travel. Refer to Illustration 2.
Start the engine.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Illustration 3 g01432992
Monitor
(A) Display
(B) Keypad
(C) Up key
(D) Left key
(E) Down key
(F) Right key
(G) Cancel key
(H) Home key
(I) OK key
(J) Menu key
Start Service Mode and input a fixed power shift pressure of 2900 kPa (420 psi).
Press menu key (J). Note: If more than thirty seconds pass between pushing the keys on the keypad, the menu mode will be cancelled and the previous display will be restored to message display (A).
Press right key (F) in order to highlight "SERVICE" menu option.
After the "SERVICE" option is highlighted, press OK key (I).
Illustration 4 g01148206
After OK key (I) is pressed, the screen in Illustration 4 will be displayed. The password for the service menu is "FFF2". The keys for direction are used to input the password. Press left key (D) or right key (F) in order to change the position of the flashing character. Press OK key (I) in order to enter the highlighted character.
After entering the last letter of the password, the monitor will continue with the "SERVICE" screen.
Repeatedly press down key (E) in order to highlight the "DEVICE TEST" line on the display.
After the "DEVICE TEST" line is highlighted, press OK key (I).
Once the "DEVICE TEST" screen is displayed, press down key (E) until "POWER SHIFT PRES" appears on the display.
When "POWER SHIFT PRES" is highlighted, press OK key (I).
Place the machine controls at the following settings: engine speed dial 10 and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings. Note: Press OK key (I) within 5 seconds after completion of Step 9.j in order to ensure high idle.
The "POWER SHIFT PRES" will now be displayed. Line 4 of the display will now change to a numeric value. These characters represent the power shift pressure (kPa).
Press left key (D) or right key (F) in order to increase or decrease the numeric value that is displayed on line 4 of the display. Pressing left key (D) decreases the power shift pressure. Pressing right key (F) increases the power shift pressure. Note:


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.