AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 2444746 - Caterpillar


2444746 ENGINE AR-COMPLETE Caterpillar parts C-15
Rating:
15
Alternative (cross code) number:
CA2444746
244-4746
2444746
Caterpillar 2444746 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 2444746 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 2444746:

TRUCK ENGINE  C-15   Caterpillar
  For full view, you need register

Information:

Used PC Nozzles (With Diesel Fuel)
Pressure To Open Value (VOP): 400-750 psi (2750-5200 kPa)
Rate of Leakage: With a pressure of 300 psi (2050 kPa), pressure reading must not be less than 100 psi (690 kPa) after 30 seconds. Therefore, permissible pressure drop is 200 psi (1380 kPa).
New PC Nozzles (With Diesel Fuel)
Pressure To Open Valve (VOP): 685-750 psi (4720-5200 kPa)
Rate of Leakage: With a pressure of 600 psi (4150 kPa), pressure reading must not be less than 200 psi (1380 kPa) after 30 seconds. Therefore, permissible pressure drop is 400 psi (2750 kPa).Test specifications with different test fluids are not known for the direct injection nozzles.
--------------- END SUPPLEMENT --------------- Because of the nature of the information in the following article, it is not written in Caterpillar Fundamental English.Here is an article of direct interest to all fuel system servicemen and people who prepare claims. Please test all fuel injection nozzles (capsule-type or pencil-type) removed from any engines before a new nozzle is used as a replacement. If the removed nozzle tests satisfactory, use it again.
Tests by Caterpillar Tractor Co., with the 5P4150 Nozzle Tester Group and in engines, have shown that many nozzles sent to Caterpillar on warranty claims did not need a replacement. The 5P4150 Nozzle Tester Group or the 8S2242 Nozzle Tester Group with the 5P4149 Conversion Group must be used to make a test on all nozzles removed from an engine, unless the nozzle shows damage. The 5P4150 Tester is the only tester that can be used for 9L6884 Nozzles in 3400 Series Direct Injection Engines. These tools and their Special Instruction Form FM055225-03 were made available to provide a quick, accurate method of testing all types of fuel nozzles.
Be sure you are thoroughly familiar with the correct procedures and specifications in the Special Instructions. For example, one Step sometimes overlooked in testing the 9L6969 Pencil-type Nozzles is the failure to remove the cap from the nozzle. This must be done to prevent a hydraulic lock when the nozzle is checked with the tester.
If you make tests on large quantities of pencil-type or capsule-type nozzles, use two testers. Use a tester for each nozzle type. This prevents leakage by eliminating repetitive tightening and loosening of the line and adapter on the tester. The former 8S2242 Group can be used for all nozzles in 1100, 3100, and 3208 Engines.
Nozzle tester for pencil-type nozzles--8S2242 Nozzle Tester Group shown.Tips For More Exact Tests
... You do not need to make tests on new capsule nozzles, but if you do make a test, install the nozzle in a precombustion chamber and tighten to the correct torque. Remove the nozzle and make the test. The tightening forces can seal the internal parts the same as if the nozzle were installed in the engine.... Do not make tests on hot nozzles. High temperatures reduce the fluid viscosity and cause too much "leak down" (pressure drop).... If the calibrating oils listed in the Special Instruction are not available, use a diesel fuel in


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.