AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 2444821 - Caterpillar


2444821 ENGINE AR-COMPLETE Caterpillar parts C-15
Rating:
49
Alternative (cross code) number:
CA2444821
244-4821
2444821
Caterpillar 2444821 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 2444821 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 2444821:

TRUCK ENGINE  C-15   Caterpillar
  For full view, you need register

Information:


Illustration 1 g01223669
(24) Port on supply line for work tool (25) Port on return line for work tool (26) Pump pressure tap (27) Pump pressure tap (34) Load valve for flow meter (35) Drive pump pressure tap (40) Flow meter inlet (41) Outlet of the flow meter
Illustration 2 g01134699
Flow meter (32) Test hose from the supply line for work tool (33) Test hose to the return line for the work tool (34) Load valve for flow meter (40) Flow meter inlet (41) Outlet of the flow meter (42) Pressure gauge for the flow meter
Connect one end of the test hose (32) to the supply line for the work tool (24) . Connect the other end of the test hose (32) to the inlet port on the flow meter (40) . Refer to Illustration 2.
Connect one end of the second test hose (33) to the return line for the work tool. Connect the other end of the test hose (33) to the outlet port on the flow meter. Refer to Illustration 2.
Illustration 3 g01454972
311D pump compartment with tool priority flow valve (26) Pressure tap (idler pump pressure) (27) Pressure tap (drive pump pressure) (37) Pressure tap (power shift pressure) (43) Tool priority flow valve (44) Tool priority flow valve for adjustment
Illustration 4 g01454975
312D, 315D, and 319D pump compartment with tool priority flow valve (26) Pressure tap (idler pump pressure) (27) Pressure tap (drive pump pressure) (37) Pressure tap (power shift pressure) (43) Tool priority flow valve (44) Tool priority flow valve for adjustment
Install a pressure gauge with a 40000 kPa (5800 psi) capacity on pressure tap (27) and pressure tap (26) for main pump pressure.
Open the load valve (34) on the flow meter to FULL OPEN.
Start the engine.
Move the engine speed dial to position 10.
Increase the oil temperature to 50 °C (122 °F).
Select Tool #5 "CUTTER" for tool priority flow. Refer to Testing and Adjusting, "Work Tool - Select" for the Tool Control System.
Illustration 5 g01433451
Right side switch panel (45) Switch for tool priority flow
Position switch (45) for tool priority flow to the ON position.
Turn load valve (34) on the flow meter CLOCKWISE until the desired work tool operating pressure is read on pressure gauge (31) .
Check that tool priority flow is within the range of the desired specification for flow to the work tool.
If the desired flow is out of the range, adjust the tool priority flow valve (43) with the following procedure.
Open the load valve (34) on the flow meter to FULL OPEN.
Position switch (45) for tool priority flow to the OFF position.
Tune the flow to the desired value by adjusting valves (44) . Turn adjusting valves (44) clockwise to decrease flow. Turn adjusting valves (44) counterclockwise to increase flow. Refer to Illustration 3 and Illustration 4.
Position switch (45) for tool priority flow to the ON position.
Adjust load valve (34) on the flow meter until the desired work tool operating pressure is read on pressure gauge (31) .Note: Adjustments to the pressure reading on gauge (31) should only be made on pressure


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.