2498295 ENGINE AR-COMPLETE Caterpillar parts
C13
Rating:
Alternative (cross code) number:
CA2498295
249-8295
2498295
CA2498295
249-8295
2498295
TRUCK ENGINE,
Compatible equipment models: 2498295:
For full view, you need register
Information:
Closing All Floating Toolbars
All of the floating toolbars can be closed at once using one of the following two icons:
Menu - Select "System" from the Main menu. Select "Screen" from the "System Menu", and then select "Close All Floating Toolbars".
Close All Floating Toolbars - Select "Close All Floating Toolbars" if this tool is displayed on one of the floating toolbars. Requesting a Surface Update
The office automatically sends a surface update when:
A machine starts up.
A new design is selected as Prime.
Illustration 6 g03209901
Surface update toolbar buttons (7) "Request Surface Update" toolbar button (8) "Request Surface Update Trim" toolbar buttonThe operator requests a surface update for the area covered by a Prime design by one of the following methods:
Select Menu > File > "Request Surface Update".
Select Menu > File > "Request Surface Update Trim"
Select the "Request Surface Update" toolbar button (7) .
Select the "Request Surface Update Trim" toolbar button (8) .Note: Request a surface update from the office before starting work in a new area and then request additional updates when needed.The office sets the size of the updated area in the office using the "Surface Update Size" Machine Configuration Utility setting. The request applies to all surfaces that are Prime on the machine. These surfaces include current elevation, ore status, coverage files, flat plane, and inclined plane.Results on Surfaces
Illustration 7 g02754316
Original surface
Illustration 8 g02754317
Surface truncated when using Request Surface Update Trim
Illustration 9 g02754318
Surface not truncated when using Request Surface UpdateAs shown in Illustrations 7 through 9 the surface updates in a specific way based on the type of request as follows:Request Surface Update Trim - The surface is truncated to the size requested.Request Surface Update - The surface is updated, but is not truncated.- ExampleAssume that the office sets Mapping > Surface Updates > Surface Update Size = 50m. The size of the updated area will be a square that is 100m x 100m around the machine origin.To update the whole surface (not truncated), select the Request Surface Update toolbar button (1) To update the surface on the machine, select the Request Surface Update Trim toolbar button (2). When selected, the office sends a truncated surface to the machine. The on-board software merges the updated truncated surface from the office with the current machine surface. The machine display shows the most recent surface available in the 100m x 100m square around the machine origin.Troubleshooting
No Input of Multicast Snippets
If there is no input, such as the input of multicast snippets to the machine, then the screen may not always redraw after a merge. If the surface does not update on the screen, trigger a screen redraw by zooming in.Compaction Data is Inappropriate
The merge surface function uses the most recent data for all surface types. For certain surface types, such as compaction and coverage (pass counts), the merge surface option results in minor disruption of data. For these surface types, the most recent data may not be the most appropriate data. - ExampleThe machine passes over some new ground before a surface update from the
All of the floating toolbars can be closed at once using one of the following two icons:
Menu - Select "System" from the Main menu. Select "Screen" from the "System Menu", and then select "Close All Floating Toolbars".
Close All Floating Toolbars - Select "Close All Floating Toolbars" if this tool is displayed on one of the floating toolbars. Requesting a Surface Update
The office automatically sends a surface update when:
A machine starts up.
A new design is selected as Prime.
Illustration 6 g03209901
Surface update toolbar buttons (7) "Request Surface Update" toolbar button (8) "Request Surface Update Trim" toolbar buttonThe operator requests a surface update for the area covered by a Prime design by one of the following methods:
Select Menu > File > "Request Surface Update".
Select Menu > File > "Request Surface Update Trim"
Select the "Request Surface Update" toolbar button (7) .
Select the "Request Surface Update Trim" toolbar button (8) .Note: Request a surface update from the office before starting work in a new area and then request additional updates when needed.The office sets the size of the updated area in the office using the "Surface Update Size" Machine Configuration Utility setting. The request applies to all surfaces that are Prime on the machine. These surfaces include current elevation, ore status, coverage files, flat plane, and inclined plane.Results on Surfaces
Illustration 7 g02754316
Original surface
Illustration 8 g02754317
Surface truncated when using Request Surface Update Trim
Illustration 9 g02754318
Surface not truncated when using Request Surface UpdateAs shown in Illustrations 7 through 9 the surface updates in a specific way based on the type of request as follows:Request Surface Update Trim - The surface is truncated to the size requested.Request Surface Update - The surface is updated, but is not truncated.- ExampleAssume that the office sets Mapping > Surface Updates > Surface Update Size = 50m. The size of the updated area will be a square that is 100m x 100m around the machine origin.To update the whole surface (not truncated), select the Request Surface Update toolbar button (1) To update the surface on the machine, select the Request Surface Update Trim toolbar button (2). When selected, the office sends a truncated surface to the machine. The on-board software merges the updated truncated surface from the office with the current machine surface. The machine display shows the most recent surface available in the 100m x 100m square around the machine origin.Troubleshooting
No Input of Multicast Snippets
If there is no input, such as the input of multicast snippets to the machine, then the screen may not always redraw after a merge. If the surface does not update on the screen, trigger a screen redraw by zooming in.Compaction Data is Inappropriate
The merge surface function uses the most recent data for all surface types. For certain surface types, such as compaction and coverage (pass counts), the merge surface option results in minor disruption of data. For these surface types, the most recent data may not be the most appropriate data. - ExampleThe machine passes over some new ground before a surface update from the