2569237 ENGINE AR-COMPLETE Caterpillar parts
C15
Rating:
Alternative (cross code) number:
CA2569237
256-9237
2569237
CA2569237
256-9237
2569237
TRUCK ENGINE,
Compatible equipment models: 2569237:
For full view, you need register
Information:
Introduction
This special instruction covers the installation procedure for 371-8164 Valve Ar on the models and applications listed above.Safety Section
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Personal injury or death can result from improperly checking for a leak.Always use a board or cardboard when checking for a leak. Escaping air or fluid under pressure, even a pin-hole size leak, can penetrate body tissue causing serious injury, and possible death.If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.
Illustration 1 g00104545
Prevent the machine from movement. Park the machine on a level surface.Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the controls before you service the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Caterpillar dealer.Required Parts
Table 1
371-8164 Valve Gp Revision -01
Item Qty Part No. Description
(1) 1 255-5607 Control Valve Gp
(2) 4 096-3044 O-Ring Seal
(3) 4 1P-3702 Rectangular Seal
(4) 4 8T-6385 Bolt
(5) 4 9X-8257 Washer Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses, on all hose assemblies, on all harness assemblies, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. 371-8164 Valve Gp
Illustration 2 g03334431
(1) 255-5607 Control Valve Gp (2) 096-3044 O-Ring Seal (3) 1P-3702 Rectangular Seal (4) 8T-6385 Bolt
This special instruction covers the installation procedure for 371-8164 Valve Ar on the models and applications listed above.Safety Section
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Personal injury or death can result from improperly checking for a leak.Always use a board or cardboard when checking for a leak. Escaping air or fluid under pressure, even a pin-hole size leak, can penetrate body tissue causing serious injury, and possible death.If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.
Illustration 1 g00104545
Prevent the machine from movement. Park the machine on a level surface.Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the controls before you service the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Caterpillar dealer.Required Parts
Table 1
371-8164 Valve Gp Revision -01
Item Qty Part No. Description
(1) 1 255-5607 Control Valve Gp
(2) 4 096-3044 O-Ring Seal
(3) 4 1P-3702 Rectangular Seal
(4) 4 8T-6385 Bolt
(5) 4 9X-8257 Washer Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses, on all hose assemblies, on all harness assemblies, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. 371-8164 Valve Gp
Illustration 2 g03334431
(1) 255-5607 Control Valve Gp (2) 096-3044 O-Ring Seal (3) 1P-3702 Rectangular Seal (4) 8T-6385 Bolt