ENGINE AR-COMPLETE 2632004 - Caterpillar

2632004 ENGINE AR-COMPLETE Caterpillar parts 324D L, 324D LN, 325D, 325D L, 329D L, M325D L MH, M325D MH

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2632004
263-2004
2632004

Weight: 1760 pounds 798 kg.

Buy ENGINE AR-COMPLETE 2632004 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, MOBILE HYD POWER UNIT,

Related part:

2632004 SHORT BLOCK 10R4139 R

2632004 ENGINE AR-COMPL 20R1691 R

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

$50.06

20 Feb 2022

US: All Star Suppli

Weigerts Hematoxylin, Solution B, 500ml
Electron Microscopy Sciences Weigerts Hematoxylin, Solution B

For full view, you need register

Compatible equipment models: 2632004:

EXCAVATOR 324D L 324D LN 325D 325D L 329D L M325D L MH M325D MH

MOBILE HYD POWER UNIT 325D Caterpillar

Information:

Crankshaft Vibration Damper and Pulley
Start By:a. remove radiator 1. Loosen bolt (4), bolt (5), and bolt (6) to the belt tightener. Remove belts (3).2. Remove bolts (2) and fan (1). 3. Remove bolt (7) and washer (8) from the crankshaft. Put enough spacers (10) on bolt (7) to get approximately 3.18 mm (.125 in.) of clearance between washer (8) and vibration damper and pulley assembly (9). Install bolt (7), washer (8), and spacers (10).
If spacers (10) are not used, damage to the bolt and/or crankshaft can result when the vibration damper and pulley are removed from the crankshaft.
4. Install tool (A) as shown, and loosen vibration damper and pulley assembly (9) from the crankshaft.5. Remove tool (A), bolt (7), washer (8), spacers (10), and vibration damper and pulley assembly (9). 6. If necessary, remove bolts (11) and vibration damper (12) from pulley (13).Install Crankshaft Vibration Damper And Pulley
Inspect the vibration damper housing for leakage or dents (damage housing). If either condition exists, a replacement of the vibration damper must be made.1. Put vibration damper (12) in position on pulley (13). Install bolts (11). 2. Put vibration damper and pulley assembly (9) in position on the crankshaft and install bolt (7) and washer (8).
The flat side of washer (8) must be installed toward vibration damper and pulley assembly (9).
3. Tighten bolt (7) to a torque of 284 to 340 N m (210 to 250 lb.ft.). Hit bolt (7) with a hammer and tighten again to a torque of 284 to 340 N m (210 to 250 lb.ft.). 4. Put belts (3) in position. Tighten bolt (4), bolt (5), and bolt (6). Use a belt tension gauge and make an adjustment of the belts. Measure the belt farthest from the engine. Tighten new belts until the gauge indication is 534 22 N (120 5 lb.ft.). Operate the engine at high idle for a minimum of 30 minutes after installing radiator and guards. Make another adjustment of the belt tension. The correct gauge indication for a used belt is 400 44 N (90 10 lb.). Tighten bolt (4), bolt (5), and bolt (6).5. Put fan (1) in position and install bolt (2).End By:a. install radiator