2640719 ENGINE AR-COMPLETE Caterpillar parts
C9
Rating:
Alternative (cross code) number:
CA2640719
264-0719
2640719
CA2640719
264-0719
2640719
GENERATOR SET,
Related part:
2640719
SHORT BLOCK
10R9870
R
Compatible equipment models: 2640719:
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01432111
Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 2 g01444452
Remove clamps (1) .
Illustration 3 g01444450
Remove bolts (3) and guard assemblies (2) and (4). The weight of each guard assembly (2) and (4) is approximately 11 kg (25 lb).
Illustration 4 g01444505
Disconnect hose assemblies (6) and tube assemblies (7) and remove the fittings. Remove bolts (5) .
Illustration 5 g01444447
Disconnect four hose assemblies (8). Disconnect three hose assemblies (9) and remove the fittings.
Illustration 6 g01444448
Disconnect hose assembly (10) and remove the fitting.
Remove pin (11). Remove bolts (13) and bracket (12) .
Illustration 7 g01444509
Remove bolts (15) and clamp (14) .
Illustration 8 g01444511
Remove retainer (16) and boot (17) .
Illustration 9 g01444513
Attach a suitable lifting device to swivel (18). The weight of swivel (18) is approximately 65 kg (143 lb). Remove swivel (18) .
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01432111
Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 2 g01444452
Remove clamps (1) .
Illustration 3 g01444450
Remove bolts (3) and guard assemblies (2) and (4). The weight of each guard assembly (2) and (4) is approximately 11 kg (25 lb).
Illustration 4 g01444505
Disconnect hose assemblies (6) and tube assemblies (7) and remove the fittings. Remove bolts (5) .
Illustration 5 g01444447
Disconnect four hose assemblies (8). Disconnect three hose assemblies (9) and remove the fittings.
Illustration 6 g01444448
Disconnect hose assembly (10) and remove the fitting.
Remove pin (11). Remove bolts (13) and bracket (12) .
Illustration 7 g01444509
Remove bolts (15) and clamp (14) .
Illustration 8 g01444511
Remove retainer (16) and boot (17) .
Illustration 9 g01444513
Attach a suitable lifting device to swivel (18). The weight of swivel (18) is approximately 65 kg (143 lb). Remove swivel (18) .
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts engine Caterpillar catalog:
2524430
ENGINE AR-CORE
C9, CX31-C9I, TH31-E61
C9, CX31-C9I, TH31-E61
2612204
ENGINE AR-CORE
C9, CX31-C9I, TH31-E61
C9, CX31-C9I, TH31-E61
3426056
ENGINE AR-COMPLETE
C9, CX31-C9I, TH31-E61
C9, CX31-C9I, TH31-E61