2752986 ENGINE AR-COMPLETE Caterpillar parts
C13
Rating:
Alternative (cross code) number:
CA2752986
275-2986
2752986
CA2752986
275-2986
2752986
TRUCK ENGINE,
Compatible equipment models: 2752986:
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
M8 by 90 mm 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the water pump is clean and free from wear and damage. If necessary, replace the water pump. Clean the gasket surface of the water pump.
Illustration 1 g03434736
Illustration 2 g03413498
Clean the gasket surface of front cover (1).
Install Tooling (A) in Position (X).
Use Tooling (A) in order to align new gasket (2) to front cover (1). Install the gasket onto the front cover.
Align water pump (3) to Tooling (A). Install the water pump to front cover (1). Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
Install bolts (4), bolts (5), and bolts (6). Refer to Illustration 1. Tighten the bolts finger tight.
Remove Tooling (A) and install the remaining bolts.
Illustration 3 g03413499
Tighten bolts (4), bolts (5), and bolts (6) in the sequence that is shown in Illustration 3 to a torque of 22 N m (195 lb in).
Install the hose to the water pump inlet. Tighten the hose clamps securely.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure. End By:
Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
M8 by 90 mm 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the water pump is clean and free from wear and damage. If necessary, replace the water pump. Clean the gasket surface of the water pump.
Illustration 1 g03434736
Illustration 2 g03413498
Clean the gasket surface of front cover (1).
Install Tooling (A) in Position (X).
Use Tooling (A) in order to align new gasket (2) to front cover (1). Install the gasket onto the front cover.
Align water pump (3) to Tooling (A). Install the water pump to front cover (1). Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
Install bolts (4), bolts (5), and bolts (6). Refer to Illustration 1. Tighten the bolts finger tight.
Remove Tooling (A) and install the remaining bolts.
Illustration 3 g03413499
Tighten bolts (4), bolts (5), and bolts (6) in the sequence that is shown in Illustration 3 to a torque of 22 N m (195 lb in).
Install the hose to the water pump inlet. Tighten the hose clamps securely.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure. End By:
Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the correct procedure.