2752993 ENGINE AR-COMPLETE Caterpillar parts
C13
Rating:
Alternative (cross code) number:
CA2752993
275-2993
2752993
CA2752993
275-2993
2752993
TRUCK ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Alkar 2752993 Main Headlights
Alkar Width: 31.51 cm || Supplementary article/supplementary information: with electric motor || Height: 25.15 cm || Bulb type: HB3; H11 || Length: 63.94 cm || Left/right-hand drive vehicle: for left-hand drive vehicles || Quality: certified quality
Alkar Width: 31.51 cm || Supplementary article/supplementary information: with electric motor || Height: 25.15 cm || Bulb type: HB3; H11 || Length: 63.94 cm || Left/right-hand drive vehicle: for left-hand drive vehicles || Quality: certified quality
For full view, you need register
Compatible equipment models: 2752993:
Information:
Remove rotator head bolt (4) from rotator gear group (5). Only two of the rotator head bolts (4) will be accessible at a time through the two inspection holes (6).
Clean the threaded bolt hole in rotator gear group (5).
Clean the new rotator head bolt (4).
Coat the entire threaded area of the new rotator head bolt (4) with 9S-3263 Thread Lock compound.
Install the new rotator head bolt (4) in rotator gear group (5).
Tighten the new rotator head bolt (4). Use appropriate tooling in order to apply the torque that is specified in table 3.
Table 3
Static inspection torque
Sales model Bolt size Torque value
CTV30 M20 520 70 N m (384 52 lb ft)
Place a mark on the new rotator head bolt (4) that was replaced. This will indicate that the bolt has been replaced. Move onto the next rotator head bolt (4). Note: Rotator head bolts (4) must be tightened in a cross pattern.
Repeat steps 2 through step 8 for all rotator head bolts (4) in rotator gear group (5). Note: Rotate the work tool in order to access all rotator head bolts (4).
Illustration 10 g03463216
Install plug (3) on both sides of the rotator. Torque the plugs to 275 35 N m (203 26 lb ft). Head Assembly
Illustration 11 g03463217
Remove rotator head bolt (7) from head assembly (8).
Clean the threaded bolt hole in head assembly (8).
Clean the new rotator head bolt (7).
Coat the entire threaded area of the new rotator head bolt (7) with 9S-3263 Thread Lock compound.
Install the new rotator head bolt (7) in head assembly (8).
Tighten the new rotator head bolt (7). Use appropriate tooling in order to apply the torque that is specified in table 3.
Table 4
Static inspection torque
Sales model Bolt size Torque value
CTV30 M20 520 70 N m (384 52 lb ft)
Place a mark on the new rotator head bolt (7) that was replaced. This will indicate that the bolt has been replaced. Move onto the next rotator head bolt (7). Note: Rotator head bolts (7) must be tightened in a cross pattern.
Repeat steps 1 through step 7 for all rotator head bolts (7) in head assembly (8). CTV40
Reference: Refer to Torque Specifications, SENR3130 for additional information on torque.Head AS
Illustration 12 g03463256If the head assembly nuts and bolts (9) must be replaced, contact your Cat dealer for additional information.Rotator GP
Illustration 13 g03463258
Remove the three covers (10) on top of the rotator housing assembly to access the lower rotator head bolts.
Remove rotator head bolt (11) from rotator gear group. Only three of the rotator head bolts (11) will be accessible at a time through the three inspection holes.
Clean the threaded bolt hole in rotator gear group.
Clean the new rotator head bolt (11).
Illustration 14 g03368210
Typical bolt
Coat 3/4 of the threaded area of the new rotator head bolt (11) with 9S-3263 Thread Lock compound.
Install the new rotator head bolt (11) in the rotator gear group.
Tighten the new rotator head bolt (11). Use appropriate tooling in order to apply the torque that is specified in