2784281 ENGINE AR-PRIMARY Caterpillar parts
C6.6
Rating:
Alternative (cross code) number:
CA2784281
278-4281
2784281
CA2784281
278-4281
2784281
INDUSTRIAL ENGINE,
Related part:
2784281
BLOCK GP-LONG
20R2682
R
Compatible equipment models: 2784281:
For full view, you need register
Information:
Introduction
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.This Special Instruction is organized into modules. Caterpillar suggests installing one module at a time.Safety
Illustration 1 g00104545Prevent the machine from movement. Park the machine on a level surface.Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the controls before you service the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Caterpillar dealer.Required Parts
Table 1
513-8845 Auxiliary Control Ar (- 00)
Part Number Description Media Number
359-8534 Front Lines Gp GEHS0359
428-8279 Pilot Lines Gp GEHS1023
359-8535 Pump Lines Gp GEHS0360
342-1891 Auxiliary Pump and Mounting Gp GEHS0357
502-1745 Medium Pressure Wiring M0072374
444-9174 Film - Calibration
Set the machine tool control system.
Reference: Excavator Tool Control System, UENR6166, "Testing and Adjusting Section", "Process for setting Up the Work Tool"Calibrate the machine electronic control system.
Reference: Excavator Tool Control System, UENR6166, "Testing and Adjusting Section", "Work Tool Parameter - Program"Set tool flows and pressures.
Reference: Excavator Tool Control System, UENR6166, "Testing and Adjusting Section", "Process for Setting Up the Work Tool"Reference: Excavator Tool Control System, UENR6166, "Testing and Adjusting Section", "Work Tool - Select"Set the proper operating and/or relief pressures and the proper flows for the tool that is attached to the machine. Refer to the Operation and Maintenance Manual of the specific work tool installed.Principles of Operation
Reference: Excavator Tool Control System, UENR6166, "Systems Operation Section", "General Information"Serial Number Identification 444-9174 Film
Caterpillar Work Tools hydraulic kits are identified with serial numbers. The serial number is printed on a film group (1). This film group should be placed on the right-hand window inside the cab.
Illustration 2 g01742203
(1) 444-9174 Film
Illustration 3 g01743196
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.This Special Instruction is organized into modules. Caterpillar suggests installing one module at a time.Safety
Illustration 1 g00104545Prevent the machine from movement. Park the machine on a level surface.Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the controls before you service the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Caterpillar dealer.Required Parts
Table 1
513-8845 Auxiliary Control Ar (- 00)
Part Number Description Media Number
359-8534 Front Lines Gp GEHS0359
428-8279 Pilot Lines Gp GEHS1023
359-8535 Pump Lines Gp GEHS0360
342-1891 Auxiliary Pump and Mounting Gp GEHS0357
502-1745 Medium Pressure Wiring M0072374
444-9174 Film - Calibration
Set the machine tool control system.
Reference: Excavator Tool Control System, UENR6166, "Testing and Adjusting Section", "Process for setting Up the Work Tool"Calibrate the machine electronic control system.
Reference: Excavator Tool Control System, UENR6166, "Testing and Adjusting Section", "Work Tool Parameter - Program"Set tool flows and pressures.
Reference: Excavator Tool Control System, UENR6166, "Testing and Adjusting Section", "Process for Setting Up the Work Tool"Reference: Excavator Tool Control System, UENR6166, "Testing and Adjusting Section", "Work Tool - Select"Set the proper operating and/or relief pressures and the proper flows for the tool that is attached to the machine. Refer to the Operation and Maintenance Manual of the specific work tool installed.Principles of Operation
Reference: Excavator Tool Control System, UENR6166, "Systems Operation Section", "General Information"Serial Number Identification 444-9174 Film
Caterpillar Work Tools hydraulic kits are identified with serial numbers. The serial number is printed on a film group (1). This film group should be placed on the right-hand window inside the cab.
Illustration 2 g01742203
(1) 444-9174 Film
Illustration 3 g01743196