2922548 ENGINE AR-COMPLETE Caterpillar parts
770
Rating:
Alternative (cross code) number:
CA2922548
292-2548
2922548
CA2922548
292-2548
2922548
TRUCK,
Compatible equipment models: 2922548:
For full view, you need register
Information:
Poor Heating
If the air flow is normal, see "Normal air flow". If the air flow is short, see "Air flow is short". If the changeover for the discharge is poor, see "Air Outlet". If the fresh air or recirculation is poor, see "Diagnostics".Air flow is short
If the blower motor rotates, refer to "The blower motor rotates". If the blower motor does not rotate, see "The blower motor does not rotate".The blower motor rotates
Diagnostics
If the rotation is correct, see steps 2, 3, 4, 5, 6, and 8. If the rotation is slow, see steps 9, 10, 11, and 12.
If the recirculation filter is clogged, clean the filter.
If the fresh air filter is clogged, clean the filter.
If an obstacle is logged at the inlet port, remove the obstacle.
If the blower motor is distorted or broken, replace the blower motor.
If the evaporator is frosted and there is voltage that is applied to the magnetic clutch, see 7. If the evaporator is frosted and there is no voltage that is applied to the magnetic clutch, the magnetic clutch is poor. Replace the magnetic clutch.
Check the clutch circuit. If necessary, replace the clutch relay. Check the wiring of the frost sensor for a short. If necessary, repair the wiring. Check the characteristics of the frost sensor. If necessary, replace the frost sensor. Check the gap between the frost sensor and the evaporator. If necessary, adjust the distance for the gap. See "Specifications".
If there is debris on the evaporator surface, clean the surface.
If power voltage drops, check the battery or check the charging surface.
If there is poor contact with the battery terminal, repair the terminal.
If the blower motor is poor, replace the motor.
If the blower high relay is poor, replace the relay. The blower motor does not rotate
Diagnostics
If the blower motor rotates only in the HI speed, see step 2. If the blower motor does not rotate in the HI, or Lo speeds, see steps 3, 4, 5, 6, 7, 8, and 9.
If the resistor has an open circuit, replace the resistor.
If a fuse has an open circuit, repair the fuse.
If the power up relay of the vehicle is poor, replace the relay.
If the blower motor is poor, replace the motor.
If the blower motor is in contact with the case, repair the motor.
If the blower switch is poor, replace the switch.
If the body ground is poor, repair the ground.
If the wiring is poor, repair the wiring.
If the power transistor is poor, replace the transistor. Normal air flow
Diagnostics
If the temperature of the water is low, wait for the temperature of the water to increase. If the water temperature is normal, see steps 2, 3, 4, 5, and 6. If the LED that is used in order to adjust the temperature is operating normally, see steps 7 and 8. If the LED that is used in order to adjust the temperature is not operating normally, see steps 9 and 10.
If air is in the circuit, remove the air.
If
If the air flow is normal, see "Normal air flow". If the air flow is short, see "Air flow is short". If the changeover for the discharge is poor, see "Air Outlet". If the fresh air or recirculation is poor, see "Diagnostics".Air flow is short
If the blower motor rotates, refer to "The blower motor rotates". If the blower motor does not rotate, see "The blower motor does not rotate".The blower motor rotates
Diagnostics
If the rotation is correct, see steps 2, 3, 4, 5, 6, and 8. If the rotation is slow, see steps 9, 10, 11, and 12.
If the recirculation filter is clogged, clean the filter.
If the fresh air filter is clogged, clean the filter.
If an obstacle is logged at the inlet port, remove the obstacle.
If the blower motor is distorted or broken, replace the blower motor.
If the evaporator is frosted and there is voltage that is applied to the magnetic clutch, see 7. If the evaporator is frosted and there is no voltage that is applied to the magnetic clutch, the magnetic clutch is poor. Replace the magnetic clutch.
Check the clutch circuit. If necessary, replace the clutch relay. Check the wiring of the frost sensor for a short. If necessary, repair the wiring. Check the characteristics of the frost sensor. If necessary, replace the frost sensor. Check the gap between the frost sensor and the evaporator. If necessary, adjust the distance for the gap. See "Specifications".
If there is debris on the evaporator surface, clean the surface.
If power voltage drops, check the battery or check the charging surface.
If there is poor contact with the battery terminal, repair the terminal.
If the blower motor is poor, replace the motor.
If the blower high relay is poor, replace the relay. The blower motor does not rotate
Diagnostics
If the blower motor rotates only in the HI speed, see step 2. If the blower motor does not rotate in the HI, or Lo speeds, see steps 3, 4, 5, 6, 7, 8, and 9.
If the resistor has an open circuit, replace the resistor.
If a fuse has an open circuit, repair the fuse.
If the power up relay of the vehicle is poor, replace the relay.
If the blower motor is poor, replace the motor.
If the blower motor is in contact with the case, repair the motor.
If the blower switch is poor, replace the switch.
If the body ground is poor, repair the ground.
If the wiring is poor, repair the wiring.
If the power transistor is poor, replace the transistor. Normal air flow
Diagnostics
If the temperature of the water is low, wait for the temperature of the water to increase. If the water temperature is normal, see steps 2, 3, 4, 5, and 6. If the LED that is used in order to adjust the temperature is operating normally, see steps 7 and 8. If the LED that is used in order to adjust the temperature is not operating normally, see steps 9 and 10.
If air is in the circuit, remove the air.
If