2947196 ENGINE AR-PRIMARY Caterpillar parts
C6.6
Rating:
Alternative (cross code) number:
CA2947196
294-7196
2947196
CA2947196
294-7196
2947196
INDUSTRIAL ENGINE,
Related part:
2947196
BLOCK GP-LONG
20R2697
R
Compatible equipment models: 2947196:
Information:
Introduction
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Safety Section
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.
Illustration 1 g00104545Prevent the machine from movement. Park the machine on a level surface.Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch before you service the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Cat dealer.Required Parts
Table 1
449-4179 Chassis Wiring Gp (- 00)
Item Qty Part No. Part Name
(1) 2 111-4836 Clip
(2) 1 450-9690 Chassis Harness As
(3) 1 7I-2673 Cable Strap
(4) 2 8T-4121 Hard Washer
(5) 2 8T-4137 Bolt
Illustration 2 g06211489
Overview of the 449-4179 Chassis Wiring Gp
Installation Procedure
Illustration 3 g06211517
Rear compartment
(HARNESS) Connect to harness (4 poles), "K856 PU", "K860 BU", "K867 YL"
(1) 111-4836 Clip
(2) 450-9690 Chassis Harness As
(4) 8T-4121 Hard Washer
(5) 8T-4137 Bolt
Route and connect harness (2) to the chassis harness as shown. Install securing hardware as shown.
Illustration 4 g06211557
Beneath manifold
(RETRACT) Connect to stem 1 RETRACT solenoid "K860 BU","K867 YL", (connect with white tape)
(EXTEND) Connect to stem 1 EXTEND solenoid "K856 PU","K867 YL"
(1) 111-4836 Clip
(2) 450-9690 Chassis Harness As
(3) 7I-2673 Cable Strap
(4) 8T-4121 Hard Washer
(5) 8T-4137 Bolt
Route and connect harness (2) to solenoid connectors as shown. Install securing hardware as shown.
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Safety Section
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.
Illustration 1 g00104545Prevent the machine from movement. Park the machine on a level surface.Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch before you service the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Cat dealer.Required Parts
Table 1
449-4179 Chassis Wiring Gp (- 00)
Item Qty Part No. Part Name
(1) 2 111-4836 Clip
(2) 1 450-9690 Chassis Harness As
(3) 1 7I-2673 Cable Strap
(4) 2 8T-4121 Hard Washer
(5) 2 8T-4137 Bolt
Illustration 2 g06211489
Overview of the 449-4179 Chassis Wiring Gp
Installation Procedure
Illustration 3 g06211517
Rear compartment
(HARNESS) Connect to harness (4 poles), "K856 PU", "K860 BU", "K867 YL"
(1) 111-4836 Clip
(2) 450-9690 Chassis Harness As
(4) 8T-4121 Hard Washer
(5) 8T-4137 Bolt
Route and connect harness (2) to the chassis harness as shown. Install securing hardware as shown.
Illustration 4 g06211557
Beneath manifold
(RETRACT) Connect to stem 1 RETRACT solenoid "K860 BU","K867 YL", (connect with white tape)
(EXTEND) Connect to stem 1 EXTEND solenoid "K856 PU","K867 YL"
(1) 111-4836 Clip
(2) 450-9690 Chassis Harness As
(3) 7I-2673 Cable Strap
(4) 8T-4121 Hard Washer
(5) 8T-4137 Bolt
Route and connect harness (2) to solenoid connectors as shown. Install securing hardware as shown.