3645753 ENGINE AR-PRIMARY Caterpillar parts
420F, 428F, 430F, 432F, 434F, 444F
Rating:
Alternative (cross code) number:
CA3645753
364-5753
3645753
CA3645753
364-5753
3645753
Weight: 685 pounds 310 kg.
BACKHOE LOADER,
Related part:
3645753
BLOCK GP-LONG
20R4053
R
Information:
The event code, 3576-15 for generator to utility transfer failure that is high - least severe (1) will become active when both of the following occur:
The system is attempting to transfer to utility power.
The "generator to utility transfer failure warning event threshold" timer expires before the transfer is successful.The event threshold set point is used to configure the time the system is allowed to attempt a transfer from generator to utility before the system stops and transfers back to generator power. The timer starts the moment the generator breaker is opened and stops when the utility breaker is read back as "closed". This set point will determine the amount of time the bus will be unpowered in the event that a transfer to utility power fails. The event must be reset once the event becomes active. When the event is active, the system will not attempt to transfer to utility until the event is reset.
View active and logged diagnostic codes to determine if there are any other diagnostics that may indicate a problem with the system which may lead to a transfer failure.
Verify EMCP set point for "generator to utility transfer failure" warning event timer limits. Ensure that the timer is set to the appropriate time allotted to complete system transfer.
Wiring: Inspect system wiring for intermittent open circuits and high resistance, loose connections, and shorts to ground between the EMCP relay output. The EMCP relay output is designated for utility breaker control to the utility breaker.Test Step 1. Check the Wiring Harness for an Open Circuit or a Short Circuit to Ground
Disconnect battery power from the engine.
Disconnect the wiring harness from the EMCP and Utility Breaker.
Measure the resistance of the wiring between the designated relay or digital output and the utility breaker or utility breaker control device. If more than 10 ohms of resistance is found, there is an open circuit or bad connection. Repair or replace the wiring. If less than 10 ohms of resistance is found, measure the battery voltage at the EMCP relay or digital output pin, and utility breaker connection point. If battery power is found at both points, there may be a problem with the utility breaker. If battery power is not present at the utility breaker but present at the EMCP, repair or replace the wiring between the EMCP and breaker connections.Results:
- STOP
The system is attempting to transfer to utility power.
The "generator to utility transfer failure warning event threshold" timer expires before the transfer is successful.The event threshold set point is used to configure the time the system is allowed to attempt a transfer from generator to utility before the system stops and transfers back to generator power. The timer starts the moment the generator breaker is opened and stops when the utility breaker is read back as "closed". This set point will determine the amount of time the bus will be unpowered in the event that a transfer to utility power fails. The event must be reset once the event becomes active. When the event is active, the system will not attempt to transfer to utility until the event is reset.
View active and logged diagnostic codes to determine if there are any other diagnostics that may indicate a problem with the system which may lead to a transfer failure.
Verify EMCP set point for "generator to utility transfer failure" warning event timer limits. Ensure that the timer is set to the appropriate time allotted to complete system transfer.
Wiring: Inspect system wiring for intermittent open circuits and high resistance, loose connections, and shorts to ground between the EMCP relay output. The EMCP relay output is designated for utility breaker control to the utility breaker.Test Step 1. Check the Wiring Harness for an Open Circuit or a Short Circuit to Ground
Disconnect battery power from the engine.
Disconnect the wiring harness from the EMCP and Utility Breaker.
Measure the resistance of the wiring between the designated relay or digital output and the utility breaker or utility breaker control device. If more than 10 ohms of resistance is found, there is an open circuit or bad connection. Repair or replace the wiring. If less than 10 ohms of resistance is found, measure the battery voltage at the EMCP relay or digital output pin, and utility breaker connection point. If battery power is found at both points, there may be a problem with the utility breaker. If battery power is not present at the utility breaker but present at the EMCP, repair or replace the wiring between the EMCP and breaker connections.Results:
- STOP
Caterpillar SIS machinery equipment:
Caterpillar SIS
432F Backhoe Loader LNR00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
420F Backhoe Loader LKH00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
420F Backhoe Loader LTG00001-02342 (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
430F Backhoe Loader LNH00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
430F Backhoe Loader LDY00001-00281 (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
434F Backhoe Loader LDH00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
444F Backhoe Loader LJJ00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
428F Backhoe Loader LBH00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
430F2 Center Pivot Backhoe Loader LYD00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
430F2 IT Center Pivot Backhoe Loader LYE00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
428F2 Side Shift Backhoe Loader LYG00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
432F2 Side Shift Backhoe Loader LYJ00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
434F2 Side Shift Backhoe Loader LYK00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
444F2 Side Shift Backhoe Loader LYL00001-UP (MACHINE) POWERED BY C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
420F2 Center Pivot Backhoe Loader LBS00001-UP (MACHINE) POWERED BY 3054C, C4.4 Engine »
364-5753
ENGINE AR-PRIMARY
Caterpillar parts catalog:
Parts engine Caterpillar catalog:
3401711
ENGINE AR-COMPLETE
434F, 444F
434F, 444F
3751284
ENGINE AR-PRIMARY
420F, 428F, 430F, 432F, 434F, 444F
420F, 428F, 430F, 432F, 434F, 444F
3401707
ENGINE AR-COMPLETE
420F, 428F, 430F, 432F
420F, 428F, 430F, 432F
3401706
ENGINE AR-COMPLETE
416F, 428F
416F, 428F
3401705
ENGINE AR
420F, 428F, 430F, 432F
420F, 428F, 430F, 432F
3401704
ENGINE AR-COMPLETE
416F, 422F, 428F
416F, 422F, 428F
3521451
ENGINE AR-PRIMARY
416F, 422F, 428F, 434F
416F, 422F, 428F, 434F
3401709
ENGINE AR-COMPLETE
434F, 444F
434F, 444F
3751283
ENGINE AR-PRIMARY
416F, 428F
416F, 428F
2396568
ENGINE AR
320D LRR
320D LRR
7C0147
ENGINE AR
3406B
3406B
3475835
ENGINE AR-COMPLETE
777C, 777D
777C, 777D
4351668
ENGINE AR-PRIMARY
938H, IT38H
938H, IT38H
1061756
ENGINE AR
950F, 950F II
950F, 950F II
3823442
ENGINE AR-CORE
3512B, 3512C
3512B, 3512C