ENGINE AR 3N3373 - Caterpillar

TECHNICAL INFORMATION BULLETIN November 24, 2004
ENGINES
MACHINES 3054E (304 00395-00829)
3056E (356 00559-01669)
315C (ANF 00298-00433)
420E (HLS 00216 KMW 00153)
430E (DDT 00222 EAT 00232)
564 (KBN 00168)
574B (CZZ 00204 RLS 00146)
AP-655C(CDG 00295-00341)
BG-2255C(CKR 00264)
CP-563E(BWE 00234-00258
CNT 00371-00612)
CP-573E(ASY 00107-00110
ASZ 00202-00205)
CP-663E(ASF 00203-00204
DAF 00206-00216)
CS-563E(ASA 00394-00604
CNG 00418-00768)
CS-573E(CEB 00200-00209
CNN 00204-00218)
CS-583E(CNX 00309-00321
DAJ 00352-00393)
CS-663E(ASB 00101-00108
DAG 00357-00407)
CS-683E(ASG 00303-00308
DAD 00326-00354)
M313C (BDR 00405-00673)
M315C (BDM 00545-00754)
M316C (BDX 00575-00851)
M318C (BCZ 00648-00968
BEB 00219-00260)
M322C (BDK 00291-00415
BDY 00303-00364)
Component Code(s) 1901SUBJECT: 221-1018 Engine ECM Problems.
This TIB is intended to assist the dealer technician in identifying possible problems related to Engine ECMs and prevent unnecessary replacement of related parts.
PROBLEM:
Under certain conditions the Engine ECM 221-1018 could momentarily enter into a reset condition during normal operations.
Engine ECM (221-1018)
In the unlikely incident that the Engine ECM goes into a reset condition during normal operation, the engine will shut down. For this reported defect the shutdown of the engine is random. The time the engine runs before the engine shuts down is not predictable. If the engine is shutting down in a predictable manner then the problem being investigated is NOT related to this reported defect.
It should be noted that there are no electronic service tool diagnostic codes related to this problem.
In order to restart the engine, the operator will be required to go through the normal start-up procedure.
Steering/Brakes (Vehicle Applications Only)
If the Engine ECM goes into a reset condition, the engine will stop. If the engine provides power for hydraulic steering and/or brake servo assistance, these functions will be lost. In this case, manual steering, service brake, and secondary brake function will still be available. It is recommended that the machine be brought to a standstill as soon as conditions allow. Both hydraulic steering and servo braking functions will be resumed once the engine has restarted.
Problem ECM Part Number and Date Codes
ECM TYPE PART NUMBER START DATE CODE END DATE CODE COMMENT
Engine ECM 221-1018 01-Dec-03 3353 06-Sept-04 2504 All 190-0416_07 parts are good.
Table 1
SOLUTION:
All ECMs manufactured on or after September 7, 2004 have the reset problem rectified, and have been 100% tested before being installed onto production engines (see detailed date codes in Table 1).
All ECMs that have a date code on or later than September 7, 2004 are good ECMs and will not be affected by the reset issue. Should a situation arise where a function is lost on a machine with the latest ECMs installed, please refer to the associated machine-troubleshooting guide.
Worldwide parts stock has been purged of suspect ECMs.
As the failure rate of these components are small, we do not intend, at this stage, to release a field rework program. We will continue to monitor the situation and will revise if needed.
Any defective components should be replaced under normal warranty.
Repair
If any of the problems detailed above occur on the machine, carry out the following diagnostic checks along with those in the service manual before replacing an ECM.
Note: Not all applications have a gauge cluster or joystick.
Verify the battery connections to the gauge cluster are secure. Check the connector for tightness.
Verify the data link connections to the gauge cluster are secure.
Verify that the connections are secure