4R9999 EXCLUDER-CRANKSHAFT SEAL Caterpillar parts
120H, 120H ES, 120H NA, 12H, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 2290, 2390, 2391, 2491, 2590, 2864C, 30/30, 3116, 3126, 3...
Rating:
Alternative (cross code) number:
CA4R9999
4R-9999
4R9999
CA4R9999
4R-9999
4R9999
Weight: 0.04 pounds 0 kg.
ARTICULATED TRUCK, WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
4R9999 EXCLUDER SEAL, CRANKSHAFT Suitable For Caterpillar 4R9999
KMP BRAND Suitable for Caterpillar
KMP BRAND Suitable for Caterpillar
4R9999 EXCLUDER SEAL, CRANKSHAFT Suitable For Caterpillar 4R9999
KMP BRAND Suitable for Caterpillar
KMP BRAND Suitable for Caterpillar
Compatible equipment models: 4R9999:
ARTICULATED TRUCK
725C
EXCAVATOR
320B
322B L
322B LN
322C
322C FM
324D
324D FM
324D FM LL
324D L
324D LN
325 L
325B
325B L
325C
325C FM
325D
325D FM
325D FM LL
325D L
325D MH
326D L
328D LCR
329D
329D L
329D LN
330C
330C FM
330C L
330C MH
330D
330D FM
330D L
330D LN
330D MH
336D
336D L
336D LN
336D2
336D2 L
336E
336E H
336E L
336E LH
336E LN
336F L
340D L
340D2 L
568 FM LL
M325D L MH
M325D MH
FORWARDER
574
GENERATOR SET
C9
KNUCKLEBOOM LOADER
539
LANDFILL COMPACTOR
816F II
LOGGER
322C
MOTOR GRADER
120H
120H ES
120H NA
12H
12M 2
12M 3
12M 3 AWD
135H
135H NA
140G
140M
140M 2
140M 3
140M 3 AWD
160M
160M 2
160M 3
160M 3 AWD
PETROLEUM PACKAGE
CX31-C9I
PETROLEUM TRANSMISSION
TH31-E61
TRACK FELLER BUNCHER
2290
2390
2391
2491
2590
511
521
521B
522
522B
532
541
541 2
551
552
552 2
TK711
TK721
TK722
TK732
TK741
TK751
TK752
TRACK-TYPE TRACTOR
30/30
D5M
D5N
D6M
D6N
D6R
D6R II
D6R III
D6R STD
D6T
D6T LGP
D6T LGPPAT
D6T XL
D7E
D7E LGP
D7R XR
DEUCE
WHEEL DOZER
814F II
Information:
Specifications
Table 1
Parameter     Value    
Fuel Supply Pressure    
83 to 586 kPa (12 to 85 psig) (1)    
Fuel Pressure to Control Valve    
10.3 to 24.1 kPa (1.5 to 3.5 psig)    
( 1 ) The recommended supply pressure range is 30-35 psig.Introduction
Use this procedure to check the regulated fuel pressure. Make sure that the fuel supply pressure is correct.Required Tools
Table 2
Required Tools    
Qty     Part Number    
1     1U-5470 Engine Pressure Gp    
1     8T-5160 Gas Regulator Setting Tool    
Illustration 1 g01192577
1U-5470 Engine Pressure Group (1) Pressure indicators (2) Zero adjustment screw (3) Pressure indicator (4) Pressure tap (5) Pressure indicatorThis tool group has an indicator that is used to read the pressure in the fuel lines. The Special Instruction, SEHS8907 is with the tool group.Test Preparation - Fuel Pressure to Control Valve
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Illustration 2 g03671390
(6) Gas line (7) Gas pressure sensor (8) Fuel control valve (9) Gas Shutoff Valve (GSOV)
Turn off the main gas valve.
De-energize GSOV (9) .
Slowly remove gas pressure sensor (7) from gas line (6) .
Install a fitting into gas line (6). Connect the 1U-5470 Engine Pressure Gp to the fitting. Refer to Illustration 1.Test Procedure - Fuel Pressure to Control Valve
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Open the main gas valve.
Energize the GSOV.
Check the engine gas pressure to the fuel control valve. If, the pressure is not 10.3 to 24.1 kPa (1.5 to 3.5 psig) refer to Adjustment Procedure - Fuel Pressure to Fuel Control Valve.Adjustment Procedure - Fuel Pressure to Fuel Control Valve
Illustration 3 g03333365
(10) Bolt (11) Cover
Remove cover (11), and install the correct tools, from the 8T-5160 Gas Regulator Setting Tool, for pressure setting adjustment.
Adjust bolt (10) to achieve desired fuel pressure to the fuel control valve.
After desired pressure is reached, install cap (11) .
Table 1
Parameter     Value    
Fuel Supply Pressure    
83 to 586 kPa (12 to 85 psig) (1)    
Fuel Pressure to Control Valve    
10.3 to 24.1 kPa (1.5 to 3.5 psig)    
( 1 ) The recommended supply pressure range is 30-35 psig.Introduction
Use this procedure to check the regulated fuel pressure. Make sure that the fuel supply pressure is correct.Required Tools
Table 2
Required Tools    
Qty     Part Number    
1     1U-5470 Engine Pressure Gp    
1     8T-5160 Gas Regulator Setting Tool    
Illustration 1 g01192577
1U-5470 Engine Pressure Group (1) Pressure indicators (2) Zero adjustment screw (3) Pressure indicator (4) Pressure tap (5) Pressure indicatorThis tool group has an indicator that is used to read the pressure in the fuel lines. The Special Instruction, SEHS8907 is with the tool group.Test Preparation - Fuel Pressure to Control Valve
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Illustration 2 g03671390
(6) Gas line (7) Gas pressure sensor (8) Fuel control valve (9) Gas Shutoff Valve (GSOV)
Turn off the main gas valve.
De-energize GSOV (9) .
Slowly remove gas pressure sensor (7) from gas line (6) .
Install a fitting into gas line (6). Connect the 1U-5470 Engine Pressure Gp to the fitting. Refer to Illustration 1.Test Procedure - Fuel Pressure to Control Valve
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Open the main gas valve.
Energize the GSOV.
Check the engine gas pressure to the fuel control valve. If, the pressure is not 10.3 to 24.1 kPa (1.5 to 3.5 psig) refer to Adjustment Procedure - Fuel Pressure to Fuel Control Valve.Adjustment Procedure - Fuel Pressure to Fuel Control Valve
Illustration 3 g03333365
(10) Bolt (11) Cover
Remove cover (11), and install the correct tools, from the 8T-5160 Gas Regulator Setting Tool, for pressure setting adjustment.
Adjust bolt (10) to achieve desired fuel pressure to the fuel control valve.
After desired pressure is reached, install cap (11) .