EXTENSION 1453261 - Caterpillar

Illustration 8 g06089595
(31) Connector, J-C2, 484-5891 Harness As
(33) 285-5405 Seat Support As
(34) 489-3079 Bracket
(35) Floor mat
(36) 6V-8931 Washer Head Screw
Center the 489-3079 Bracket (34) on the left rear 285-5405 Seat Support As (33). Refer to Illustration 8.
Drill three pilot holes with a 7/32 drill bit. Use the 489-3079 Bracket (34) as a template for these holes.
Fasten the 489-3079 Bracket (34) using three 6V-8931 Washer Head Screw (36).Electrical Connections
The following section covers the connection of the 484-5891 Harness As to the power supply and data link of the machine.
Illustration 9 g06089616
(37) Wires from 484-5891 Harness As
(38) Partial view of 484-5891 Harness As
(39) Connector, J-C4, 484-5891 Harness As
(40) Wires from the Cab Harness As
(41) Cab Harness Connector, C-C2
(42) Cab Harness Connector, C-C52Note: Each connector on 484-5891 Harness As is labeled. The label is formatted as "J-C#".
Remove the wires from the existing Cab Harness Connector (41). Refer to Illustration 9 and Table 3.
Table 3
Cab Harness Connector (C-C2) (41) Wires from Cab Harness As (40)
C-C2, Position 32 F711-C293 YL
C-C2, Position 33 F712-C279 GN
Insert the wires from 484-5891 Harness As (37) into the existing Cab Harness Connector (41). Refer to Illustration 9 and Table 4.
Table 4
Cab Harness Connector (C-C2) (41) Wires from 484-5891 Harness As (37)
C-C2, Position 34 F712-J35 GN
C-C2, Position 35 F711-J30 YL
Insert the wires from the Cab Harness As (40) into the 484-5891 Harness As connector (J-C4) (39). Refer to Illustration 9 and Table 5
Table 5
Connector (J-C4) on the 484-5891 Harness As (39) Wires from the Cab Harness As (40)
J-C4, Position 1 F711-C293 YL
J-C4, Position 2 F712-C279 GN Note: Step 4 provides the power, ground, and key switch to the new K-Series Medium Wheel Loader Telematics Kit.
Connect J-C5 of the 484-5891 Harness As (38) to the Cab Harness Connector (C-C52) (42) "Power Connection".
Illustration 10 g06089651
K-Series Medium Wheel Loaders 484-5891 Harness As
(43) Connects to Machine Harness C-C52
(44) Wires are inserted into the Cab Harness Connector C-C2
(45) Wires removed from the Cab Harness Connector C-C2 are inserted into J-C4System Installation Verification
Electrical Validation
Turn on the power to the equipment once the following have been properly connected:
Network manager
Wires from the retrofit harness for battery positive, battery negative, and key switch powerSoftware Validation
Use Special Instruction, REHS8850, "Installation Procedure for the Elite Product Link™ PLE601, PLE641, and PLE631 Systems", Flash the PLE641 or PLE631 Product Link System Using Winflash for the procedure to flash the Product Link ECMs through Winflash.
Use Special Instruction, REHS8850, "Installation Procedure for the Elite Product Link™ PLE601, PLE641, and PLE631 Systems", Upload Configuration File to upload the configuration file 484-3319. This procedure is used to upload the configuration file to the Telematics ECM (network manager) using the Ethernet cable and the newly installed VIMS service port.
Follow the procedure in Special Instruction, REHS8850, "Installation Procedure for the Elite Product Link™ PLE601, PLE641, and PLE631 Systems", Set the Product ID on the PLE601 Network Manager. This procedure programs the machine serial number into the Product ID field using the Cat® Electronic Technician (Cat ET) Service Tool and the Communications Adapter.
Launch the Cat® Electronic Technician (Cat ET)