3283560 EXTENSION GP-SCREED Caterpillar parts
AP1000E, AP1055E, BG1000E, BG1055E
Rating:
Alternative (cross code) number:
CA3283560
328-3560
3283560
CA3283560
328-3560
3283560
ASPHALT PAVER,
Number on catalog scheme:
9
For full view, you need register
Information:
Using the 6V-6106 Dial Indicator Gp With A Reduced Calibration Dimension
Table 1
Required Tools
Part Number Part Description Qty
6V-6106 Dial Indicator Gp 1
1U-8815 Indicator Contact Point 1
Adjust the position of the dial indicator on the indicator bracket so that the dial indicator reads 6.00 mm (0.236 inch). Refer to the appropriate Steps in the Testing and Adjusting, "Installation of Governor on 1U-7326 Governor Calibration Bench " section in this manual for more information. Tighten the locking screw on the dial indicator in order to lock the dial indicator in position.The 6.00 mm (0.236 inch) dimension now becomes the reference point for all other adjustments made on the calibration bench. All of the other governor output dimensions must be reduced by 2.00 mm (0.079 inch) since the 6.00 mm (0.236 inch) reference point is 2.00 mm (0.079 inch) less than the 8.00 mm (0.315 inch) reference point using this modified method.Using the Programmable 1U-8869 Dial Indicator
Table 2
Required Tools
Part Number Part Description Qty
1U-8869 Dial Indicator 1
6V-2030 Extension 1
1U-8815 Indicator Contact Point 1
1U-7316 Calibration Pin Group 1
Turn on the dial indicator and set the dial indicator to reverse mode. Set the dial indicator to reverse mode by pressing the "+/-" button so that the dash (-) appears in the display under the "REV" heading. This setting will allow the dial indicator to display lower values as the stem is pushed in.
Preset the dial indicator to 8.00 mm (0.315 inch). The procedure for presetting the dial indicator is described in the operation manual for the dial indicator.
Install the extension and the contact point on the dial indicator.
Install the 1U-7316 Calibration Pin Group in the governor output clevis. Hook up the throttle spring so that the calibration pin is held tightly against the governor calibration face. The spring will hold the throttle in the high idle position.
Connect the test bench to an electrical outlet.
Turn the switch for the pump to the ON position.
Press the red "zero" button on the dial indicator and insert the dial indicator into the bracket on the calibration bench.
After the tip of the dial indicator contacts the governor output clevis pin, continue to slide the dial indicator into the indicator bracket. When the dial indicator reads -3.00 to -2.75 mm (-0.118 to -0.108 inch), lock the dial indicator in position with the setscrew. This step will ensure proper travel of the dial indicator.
Push the "preset" button on the dial indicator twice. The dial indicator should read 8.00 mm (0.315 inch).
Actuate the throttle in order to ensure that the 8.00 mm (0.315 inch) reference point has not changed.
Remove the calibration pin from the governor output clevis and proceed with the desired checking or the desired adjusting procedures.
Table 1
Required Tools
Part Number Part Description Qty
6V-6106 Dial Indicator Gp 1
1U-8815 Indicator Contact Point 1
Adjust the position of the dial indicator on the indicator bracket so that the dial indicator reads 6.00 mm (0.236 inch). Refer to the appropriate Steps in the Testing and Adjusting, "Installation of Governor on 1U-7326 Governor Calibration Bench " section in this manual for more information. Tighten the locking screw on the dial indicator in order to lock the dial indicator in position.The 6.00 mm (0.236 inch) dimension now becomes the reference point for all other adjustments made on the calibration bench. All of the other governor output dimensions must be reduced by 2.00 mm (0.079 inch) since the 6.00 mm (0.236 inch) reference point is 2.00 mm (0.079 inch) less than the 8.00 mm (0.315 inch) reference point using this modified method.Using the Programmable 1U-8869 Dial Indicator
Table 2
Required Tools
Part Number Part Description Qty
1U-8869 Dial Indicator 1
6V-2030 Extension 1
1U-8815 Indicator Contact Point 1
1U-7316 Calibration Pin Group 1
Turn on the dial indicator and set the dial indicator to reverse mode. Set the dial indicator to reverse mode by pressing the "+/-" button so that the dash (-) appears in the display under the "REV" heading. This setting will allow the dial indicator to display lower values as the stem is pushed in.
Preset the dial indicator to 8.00 mm (0.315 inch). The procedure for presetting the dial indicator is described in the operation manual for the dial indicator.
Install the extension and the contact point on the dial indicator.
Install the 1U-7316 Calibration Pin Group in the governor output clevis. Hook up the throttle spring so that the calibration pin is held tightly against the governor calibration face. The spring will hold the throttle in the high idle position.
Connect the test bench to an electrical outlet.
Turn the switch for the pump to the ON position.
Press the red "zero" button on the dial indicator and insert the dial indicator into the bracket on the calibration bench.
After the tip of the dial indicator contacts the governor output clevis pin, continue to slide the dial indicator into the indicator bracket. When the dial indicator reads -3.00 to -2.75 mm (-0.118 to -0.108 inch), lock the dial indicator in position with the setscrew. This step will ensure proper travel of the dial indicator.
Push the "preset" button on the dial indicator twice. The dial indicator should read 8.00 mm (0.315 inch).
Actuate the throttle in order to ensure that the 8.00 mm (0.315 inch) reference point has not changed.
Remove the calibration pin from the governor output clevis and proceed with the desired checking or the desired adjusting procedures.
Caterpillar SIS machinery equipment:
Caterpillar SIS
AP1055E BG1055E Asphalt Paver FRR00001-UP (MACHINE) POWERED BY C7.1 Engine »
328-3560
EXTENSION GP-SCREED
AP1055E Asphalt Paver TRS00001-UP (MACHINE) POWERED BY C6.6 Engine »
328-3560
EXTENSION GP-SCREED
AP1000E BG1000E Asphalt Paver RTT00001-UP (MACHINE) POWERED BY C7.1 Engine »
328-3560
EXTENSION GP-SCREED
AP1000E Asphalt Paver DKH00001-UP (MACHINE) POWERED BY C6.6 Engine »
328-3560
EXTENSION GP-SCREED
Caterpillar parts catalog:
Parts extension Caterpillar catalog:
307B, 311B, 312B, 325B L, 330B, 330B L, 345B II, 345B L, 345C, 345D, 345D L, 349D, 349D L, 365B, 521B, 522B, 770, 772, 773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 776C, 777, 777B, ...
1G5370
EXTENSION-CURVE
10-20B, 8-16B, AP-1000, AP-1000B, AP-1050, AP-1055B, AP-600D, AP-650B, AP-655C, AP-655D, AP-800, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, AS2251, AS2301, AS2302, BG-225B, BG-225C, BG-2455C...
10-20B, 8-16B, AP-1000, AP-1000B, AP-1050, AP-1055B, AP-600D, AP-650B, AP-655C, AP-655D, AP-800, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, AS2251, AS2301, AS2302, BG-225B, BG-225C, BG-2455C...
1090734
EXTENSION-VALVE
AP-1000B, AP-600D, AP-800C, AP-800D, AP-900B, AP1000E, BG-225B, BG-260D, BG1000E, BG600D
AP-1000B, AP-600D, AP-800C, AP-800D, AP-900B, AP1000E, BG-225B, BG-260D, BG1000E, BG600D
1072288
EXTENSION AS
10 FT, 10-20B, 10B, AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455C, BG-2455D, BG-245C, BG-260D, BG100...
10 FT, 10-20B, 10B, AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455C, BG-2455D, BG-245C, BG-260D, BG100...
1072290
EXTENSION AS
10 FT, AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, ...
10 FT, AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, ...
2157555
EXTENSION AS
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, B...
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, B...
2157556
EXTENSION AS
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, B...
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, B...
2157557
EXTENSION AS
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, B...
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, B...
2157558
EXTENSION AS
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, B...
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, B...
3380872
EXTENSION AS
AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E
AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E
3380873
EXTENSION AS
AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E
AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E
3309094
EXTENSION
BG1000E, BG1055E
BG1000E, BG1055E
3506034
EXTENSION GP-SCREED
AP555E, BG500E
AP555E, BG500E
3412290
EXTENSION AR-SCREED
AP555E
AP555E
3501625
EXTENSION AR
AP555E, BG500E
AP555E, BG500E
3045239
EXTENSION GP-SCREED
AP-600D, AP-655D
AP-600D, AP-655D
2928833
EXTENSION GP-SCREED
AP-600D, AP-655D
AP-600D, AP-655D
2918020
EXTENSION GP-SCREED
AP-600D, AP-655D
AP-600D, AP-655D
6N1173
EXTENSION GP-DRAIN
776, 777
776, 777