3872082 EXTENSION GP-FENDER Caterpillar parts
950H, 962H
Rating:
Alternative (cross code) number:
CA3872082
387-2082
3872082
CA3872082
387-2082
3872082
WHEEL LOADER,
Number on catalog scheme:
3
For full view, you need register
Information:
trouble code is not active or logged.
Proceed to Test Step 2.
2. Use the "System Communication Status" to Determine the Communication Issue
A. Connect Cat ET.
B. Click the "Diagnostics" tab on the tool bar.
C. Select the "System Communication Status" option from the drop-down list.
Note: The "Aftertreatment #1 Intake NOx Level Sensor" is displayed as "Aftertreatment #1 Information #1" in some versions of software.
Component Identified
Result: A 625-9 code is present.
Check the configuration of the secondary Electronic Control Module (ECM) to make sure that it is configured for the correct location.
The secondary ECM is Device 2.
Proceed to Test Step 7.
Result: A -9 code is active. Refer to the above -9 detected problems for additional information.
Proceed to Test Step 6.
Result: A -14 code is active. Refer to the above -14 detected problems for additional information.
If the NOx sensors are listed as ECM 2, proceed to Test Step 3.
For all other components, proceed to Test Step 4.
3. Check the Part Number of the Component
A. Locate the part number for the component that was identified by the "System Communication Status".
B. Check to see if the part number is correct for the application.
Part Number
Result: The part number is incorrect for the application.
Repair: Replace the component with the correct part number. Refer to Special Instruction, REHS8151 for special handling instructions if replacing a NOx sensor.
Proceed to Test Step 10.
Result: The part number is correct for the application.
Proceed to Test Step 4.
4. Check for Incorrect Configuration Parameters
A. Connect Cat ET.
B. Use Cat ET to verify that the correct parameters are being used.
Parameters
Result: The parameters are correct.
Proceed to Test Step 5.
Result: The parameters are not correct.
Repair: Input the correct parameters. Refer to Troubleshooting, "Configuration Parameters" for additional information.
If the problem is not resolved, proceed to Test Step 5.
5. Ensure that the latest Flash File Software is Installed in the ECM
A. Connect Cat ET.
B. Use Cat ET to verify that the correct flash file is being used.
Flash File
Result: The latest flash file is installed.
Proceed to Test Step 10.
Result: The latest flash file is not installed.
Repair: Perform the following procedure:
1. Download the latest flash file from SIS web.
2. Install the software into the ECM.
Refer to Troubleshooting, "ECM Software - Install" for additional information.
Proceed to Test Step 10.
Illustration 2 g03846524
Device 1 present
(1) Column 1
Illustration 3 g03846007
Device 1 and Device 2 present
(1) Column 1
(2) Multiple Device 1 and Device 2 can be displayed
(3) Device 2 is the affected ECM/device that cannot be recognized by Device 1. Device 2 is the ECM/device with the problem.
Table 4
Troubleshooting Test Steps Values Results
6. Use the System Communication Status to Determine the Cause
A. Determine if both Device 1 and Device 2 are present in the "ECM's" column (1) within the "System Communication Status" screen. Refer to Illustration 3.
Note: The "Aftertreatment #1 Intake NOx Level Sensor" is displayed as "Aftertreatment #1 Information #1" in some versions of software.
Component Identified
Result: Device 1 and Device 2 are both
Proceed to Test Step 2.
2. Use the "System Communication Status" to Determine the Communication Issue
A. Connect Cat ET.
B. Click the "Diagnostics" tab on the tool bar.
C. Select the "System Communication Status" option from the drop-down list.
Note: The "Aftertreatment #1 Intake NOx Level Sensor" is displayed as "Aftertreatment #1 Information #1" in some versions of software.
Component Identified
Result: A 625-9 code is present.
Check the configuration of the secondary Electronic Control Module (ECM) to make sure that it is configured for the correct location.
The secondary ECM is Device 2.
Proceed to Test Step 7.
Result: A -9 code is active. Refer to the above -9 detected problems for additional information.
Proceed to Test Step 6.
Result: A -14 code is active. Refer to the above -14 detected problems for additional information.
If the NOx sensors are listed as ECM 2, proceed to Test Step 3.
For all other components, proceed to Test Step 4.
3. Check the Part Number of the Component
A. Locate the part number for the component that was identified by the "System Communication Status".
B. Check to see if the part number is correct for the application.
Part Number
Result: The part number is incorrect for the application.
Repair: Replace the component with the correct part number. Refer to Special Instruction, REHS8151 for special handling instructions if replacing a NOx sensor.
Proceed to Test Step 10.
Result: The part number is correct for the application.
Proceed to Test Step 4.
4. Check for Incorrect Configuration Parameters
A. Connect Cat ET.
B. Use Cat ET to verify that the correct parameters are being used.
Parameters
Result: The parameters are correct.
Proceed to Test Step 5.
Result: The parameters are not correct.
Repair: Input the correct parameters. Refer to Troubleshooting, "Configuration Parameters" for additional information.
If the problem is not resolved, proceed to Test Step 5.
5. Ensure that the latest Flash File Software is Installed in the ECM
A. Connect Cat ET.
B. Use Cat ET to verify that the correct flash file is being used.
Flash File
Result: The latest flash file is installed.
Proceed to Test Step 10.
Result: The latest flash file is not installed.
Repair: Perform the following procedure:
1. Download the latest flash file from SIS web.
2. Install the software into the ECM.
Refer to Troubleshooting, "ECM Software - Install" for additional information.
Proceed to Test Step 10.
Illustration 2 g03846524
Device 1 present
(1) Column 1
Illustration 3 g03846007
Device 1 and Device 2 present
(1) Column 1
(2) Multiple Device 1 and Device 2 can be displayed
(3) Device 2 is the affected ECM/device that cannot be recognized by Device 1. Device 2 is the ECM/device with the problem.
Table 4
Troubleshooting Test Steps Values Results
6. Use the System Communication Status to Determine the Cause
A. Determine if both Device 1 and Device 2 are present in the "ECM's" column (1) within the "System Communication Status" screen. Refer to Illustration 3.
Note: The "Aftertreatment #1 Intake NOx Level Sensor" is displayed as "Aftertreatment #1 Information #1" in some versions of software.
Component Identified
Result: Device 1 and Device 2 are both
Caterpillar SIS machinery equipment:
Caterpillar SIS
950H Wheel Loader JAD00001-UP (MACHINE) POWERED BY C7 Engine »
387-2082
EXTENSION GP-FENDER
962H Wheel Loader MAL00001-UP (MACHINE) POWERED BY C7 Engine »
387-2082
EXTENSION GP-FENDER
950H Wheel Loader MXL00001-UP (MACHINE) POWERED BY C7 Engine »
387-2082
EXTENSION GP-FENDER
962H Wheel Loader PCW00001-UP (MACHINE) POWERED BY C7 Engine »
387-2082
EXTENSION GP-FENDER
962H Wheel Loader SSA00001-UP (MACHINE) POWERED BY C7.2 Engine »
387-2082
EXTENSION GP-FENDER
950H Wheel Loader JLX00001-UP (MACHINE) POWERED BY C7.2 Engine »
387-2082
EXTENSION GP-FENDER
Caterpillar parts catalog:
Parts extension Caterpillar catalog:
3925605
EXTENSION GP-FENDER
950H, 962H
950H, 962H
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 24M, 769D, 771D, 773D, 773E, 775D, 777D, 784C, 785, 785B, 785C, 785D, 789, 789...
1733083
EXTENSION GP-BACKREST
120H, 120H NA, 12H, 12H NA, 135H, 135H NA, 140H, 140H NA, 143H, 14H, 14H NA, 160H, 160H NA, 163H, 16H, 16H NA, 561N, 583R, 583T, 587R, 587T, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 96...
120H, 120H NA, 12H, 12H NA, 135H, 135H NA, 140H, 140H NA, 143H, 14H, 14H NA, 160H, 160H NA, 163H, 16H, 16H NA, 561N, 583R, 583T, 587R, 587T, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 96...
1413889
EXTENSION
950 GC, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K, IT62G II, IT62H
950 GC, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K, IT62G II, IT62H
3678376
EXTENSION GP-BACKREST
950H, 962H, 966H, 972H, 980H, 986H
950H, 962H, 966H, 972H, 980H, 986H
8I0520
EXTENSION GP-SCREED
10 FT, 10-20B, 8 FT, 8-16B, AP-1055D, AP-650B, AP-655C, AP-800C, AP-800D, BG-225B, BG-225C, BG-2455D, BG-260D
10 FT, 10-20B, 8 FT, 8-16B, AP-1055D, AP-650B, AP-655C, AP-800C, AP-800D, BG-225B, BG-225C, BG-2455D, BG-260D
1776816
EXTENSION GP-SCREED
AP-1000B, AP-900B
AP-1000B, AP-900B
8X0974
EXTENSION AS-TAIL
789, 789B, 793, 793B, 793C
789, 789B, 793, 793B, 793C
4N0312
EXTENSION GP-EXHAUST
910, 931, 931B, 931C, 935B, 935C, D3, D3B, D3C, D4B, D4C, G910, IT12
910, 931, 931B, 931C, 935B, 935C, D3, D3B, D3C, D4B, D4C, G910, IT12
1N3075
EXTENSION GP-EXHAUST
613C, 613C II
613C, 613C II
24H, 5130, 5130B, 5230, 5230B, 69D, 769D, 771D, 773D, 775D, 776D, 777D, 784C, 785C, 789C, 793C, 824G, 825G, 826G, 844, 854G, 914G, 924G, 924GZ, 924H, 924HZ, 928G, 928HZ, 930G, 938G, 938G II, 950G, 950...
1994206
EXTENSION GP-AUGER
AP-1055D, AP-600D, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-2455D, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D
AP-1055D, AP-600D, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-2455D, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D
1988287
EXTENSION GP-AUGER
AP-1055D, AP-600D, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-2455D, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D
AP-1055D, AP-600D, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-2455D, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D
6I0138
EXTENSION GP-EXHAUST
65C, 65E, 70C, 75C, 75D, 75E, 85C, 85D, 85E, 938H, 95E, IT38H
65C, 65E, 70C, 75C, 75D, 75E, 85C, 85D, 85E, 938H, 95E, IT38H
2320362
EXTENSION GP-FUMES DISPOSAL
824G II, 824H, 825G II, 825H, 834G, 834H, 988G, 988H
824G II, 824H, 825G II, 825H, 834G, 834H, 988G, 988H
1546650
EXTENSION GP-FENDER
906, 908
906, 908