7G8458 EXTENSION Caterpillar parts
561D, D5B
Rating:
Alternative (cross code) number:
CA7G8458
7G-8458
7G8458
CA7G8458
7G-8458
7G8458
Weight: 55 pounds 24 kg.
PIPELAYER, TRACK-TYPE TRACTOR,
Information:
Removal Procedure
Start By:
Remove the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Illustration 1 g03466763
Cut cable straps (4) from wiring harness assembly (3). Note: Note the position of cable straps that attach the wiring harness assembly to the ECM mounting bracket.
Remove bolt (7) from bracket (4) for plastic tube assembly. Position the bracket away from ECM mounting bracket (1).
Slide locking tab into the unlocked position. Disconnect wiring harness (5) from atmospheric pressure sensor (6) (not shown).
Remove bolts (2) from ECM mounting bracket (1).
Remove ECM mounting bracket (1) from the cylinder block.
If necessary, remove atmospheric pressure sensor (6) (not shown) from the ECM mounting bracket. Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure. Installation Procedure
Illustration 2 g03466763
Ensure that ECM mounting bracket (1) for the electronic control module is clean and free from damage. If the mounting bracket is damaged, replace the bracket.
If necessary, install atmospheric pressure sensor (6) (not shown) to ECM mounting bracket (1). Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure.
Position ECM mounting bracket (1) onto the cylinder block.
Install bolts (2) to ECM mounting bracket (1). Tighten the bolts to a torque of 22 N m (195 lb in).
Connect harness assembly (5) to atmospheric pressure sensor (6) (not shown). Slide the locking tab into the locked position.
Position bracket (4) for plastic tube assembly onto ECM mounting bracket (1). Install bolt (7) to the bracket for plastic tube assembly. Tighten the bolt to a torque of 22 N m (195 lb in)
Install new cable straps (4) to wiring harness assembly (3). Note: Ensure that the cable straps meet the Original Equipment Manufactures (OEM) specifications.End By:
Install the electronic control module. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Start By:
Remove the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Illustration 1 g03466763
Cut cable straps (4) from wiring harness assembly (3). Note: Note the position of cable straps that attach the wiring harness assembly to the ECM mounting bracket.
Remove bolt (7) from bracket (4) for plastic tube assembly. Position the bracket away from ECM mounting bracket (1).
Slide locking tab into the unlocked position. Disconnect wiring harness (5) from atmospheric pressure sensor (6) (not shown).
Remove bolts (2) from ECM mounting bracket (1).
Remove ECM mounting bracket (1) from the cylinder block.
If necessary, remove atmospheric pressure sensor (6) (not shown) from the ECM mounting bracket. Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure. Installation Procedure
Illustration 2 g03466763
Ensure that ECM mounting bracket (1) for the electronic control module is clean and free from damage. If the mounting bracket is damaged, replace the bracket.
If necessary, install atmospheric pressure sensor (6) (not shown) to ECM mounting bracket (1). Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure.
Position ECM mounting bracket (1) onto the cylinder block.
Install bolts (2) to ECM mounting bracket (1). Tighten the bolts to a torque of 22 N m (195 lb in).
Connect harness assembly (5) to atmospheric pressure sensor (6) (not shown). Slide the locking tab into the locked position.
Position bracket (4) for plastic tube assembly onto ECM mounting bracket (1). Install bolt (7) to the bracket for plastic tube assembly. Tighten the bolt to a torque of 22 N m (195 lb in)
Install new cable straps (4) to wiring harness assembly (3). Note: Ensure that the cable straps meet the Original Equipment Manufactures (OEM) specifications.End By:
Install the electronic control module. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Caterpillar parts catalog:
Parts extension Caterpillar catalog:
1F1342
EXTENSION-PIPE
D4D, D4E, D5, D5B, D5E, D6C
D4D, D4E, D5, D5B, D5E, D6C
3P5755
EXTENSION
561C, D5, D5B
561C, D5, D5B
3P5735
EXTENSION
D5, D5B
D5, D5B
3V2514
EXTENSION ASSEM.
955K, 955L
955K, 955L
3P5755
EXTENSION
561C, D5, D5B
561C, D5, D5B
6P9472
EXTENSION
583K
583K
4F2514
EXTENSION
25, 44
25, 44
3S3473
EXTENSION
572G, 983
572G, 983
5G4734
EXTENSION
D3B, D3C
D3B, D3C
3V3605
EXTENSION
955K, 955L
955K, 955L
8P1691
EXTENSION
572G
572G
3P5735
EXTENSION
D5, D5B
D5, D5B