3E3880 EYEBOLT Caterpillar parts
5230, 5230B, 824K, 825K, 826K, 836H, 836K
Rating:
Alternative (cross code) number:
CA3E3880
3E-3880
3E3880
CA3E3880
3E-3880
3E3880
Weight: 1 pounds 0 kg.
Information:
LENGTH TO EYE CENTERLINE
76.335
mm
RING ID
41.13
mm
RING OD
75.33
mm
SHOULDER DIAMETER
38
mm
THREAD LENGTH
30.5
WIDTH
17.1
THREAD SIZE
M20X2.5
LANDFILL COMPACTOR, WHEEL DOZER,
Compatible equipment models: 3E3880:
Information:
Measure the total clearance between the boom and the upper frame at the bore for the boom foot pin assembly. The total clearance of Dimension (a) plus Dimension (b) must not be more than 1.0 mm (0.04 inch). If the total clearance is less than 1.0 mm (0.04 inch), the addition of shims between the boom and the upper frame will not be required. If the total clearance is more than 1.0 mm (0.04 inch), add the correct thickness of shims in order to obtain the required clearance.
Use the following table to determine the correct shims (25).
Table 2
Table for Shims (25)    
Shim    Thickness (mm)    
166-1487     2.0 (2)    
113-2127     0.5    
093-0084     1.0    
093-0116     2.0    
( 2 ) This shim is required to be used. This shim must be next to the boom.
Illustration 6 g01226791
If shims (25) need to be installed, attach a suitable lifting device to Tooling (C). The weight of Tooling (C) is approximately 136 kg (300 lb). Attach Tooling (C) to pin assembly (23). Use Tooling (C) in order to remove pin assembly (23). The combined weight of Tooling (C) and pin assembly (23) is approximately 245 kg (540 lb).
Install the correct amount of shims. Repeat Step 6.
Illustration 7 g01225068
Remove Tooling (C) and the suitable lifting device. Install bolt (24) that retains pin assembly (23) .
Illustration 8 g01225071
Connect harness assembly (19). Connect hose assemblies (18), (20), (21), and (22). Tighten hose assemblies (18) and (20) to a torque of 76 4 N m (56 3 lb ft).
Illustration 9 g01225070
Connect hose assemblies (17) .
Illustration 10 g01212931
Illustration 11 g01212925
Position handhold (11) and bolts (12). Install bolts (13). Close cover (10) of the storage box.
Illustration 12 g01212899
Install step (9). Install bolts (8) .
Illustration 13 g01212891
Install cover (7). Install bolts (6) .
Illustration 14 g01225067
Use Tooling (A) in order to drive pin (5) so that the pin is flush with the boom. Remove Tooling (A) and install Tooling (A) onto the other side of pin (5) .Attach a suitable lifting device to boom cylinder (3). The weight of boom cylinder (3) is approximately 380 kg (838 lb).Raise boom cylinder (3) into position. Install any shims that were present. Install Tooling (A) into pin (5). Use a hammer to drive pin (5) into boom cylinder (3). Remove Tooling (A). Repeat for the other boom cylinder (3) .
Illustration 15 g01225073
Install the plate (4) and the spacer. Install bolts (2). Connect grease hose assembly (1) .End By: Install the stick. Refer to Disassembly and Assembly, "Stick - Install".
Caterpillar parts catalog:
Parts eyebolt Caterpillar catalog:
3E3879
EYEBOLT
320C FM, 3406C, 3406E, 3412C, 3456, 345C, 3508, 3508B, 3512, 3512B, 3516, 3516B, 5130, 5130B, 5230, 5230B, C18
320C FM, 3406C, 3406E, 3412C, 3456, 345C, 3508, 3508B, 3512, 3512B, 3516, 3516B, 5130, 5130B, 5230, 5230B, C18
4C8358
EYEBOLT
5130, 5130B, 5230, 844K, 854K, 990K, 992K, 993K, D10T2, D11T
5130, 5130B, 5230, 844K, 854K, 990K, 992K, 993K, D10T2, D11T
1583059
EYEBOLT
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, CB-214D, CB-214E, TK711, TK721, TK722, TK732, TK741, TK751, TK752
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, CB-214D, CB-214E, TK711, TK721, TK722, TK732, TK741, TK751, TK752
3E3881
EYEBOLT
115, 330C FM, 330D FM, H110E S, PF-290B, PS-150C, PS-200B, PS-360B, PS-360C
115, 330C FM, 330D FM, H110E S, PF-290B, PS-150C, PS-200B, PS-360B, PS-360C
1031651
EYEBOLT
RR-250, SS-250
RR-250, SS-250
1134876
EYEBOLT AS
PS-300B
PS-300B
0349458
EYEBOLT
RM-350B, SM-350
RM-350B, SM-350
1086247
EYEBOLT
AP-1000B, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-2455C, BG-245C
AP-1000B, AP-650B, AP-800C, AP-800D, BG-225B, BG-225C, BG-2455C, BG-245C
1913129
EYEBOLT
320B FM LL
320B FM LL
3Q7757
EYEBOLT
320 L, 322 LN, 330 L
320 L, 322 LN, 330 L
6R0629
EYEBOLT
CP-433B
CP-433B
1139255
EYEBOLT
SS-250
SS-250
1C4251
EYEBOLT
PR-750B
PR-750B
3E3882
EYEBOLT
5110B, AD45B, AD55
5110B, AD45B, AD55