5I8772 EYEBOLT Caterpillar parts
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B, 330C L
Rating:
Alternative (cross code) number:
CA5I8772
5I-8772
5I8772
CA5I8772
5I-8772
5I8772
Weight: 0.35 pounds 0 kg.
EXCAVATOR,
Compatible equipment models: 5I8772:
Number on catalog scheme:
10
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the bottom guard. Refer to Disassembly and Assembly, " Bottom Guard - Remove and Install".Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01250304
Remove bolts (1). Remove sheet (2) .
Illustration 2 g01250305
Turn valve (3) to the OFF position.
Illustration 3 g01250536
Disconnect hose assemblies (4) and (5) .
Remove bolts (6) and fuel transfer pump (7) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 4 g01250536
Position fuel transfer pump (7). Install bolts (6) .
Connect hose assemblies (5) and (4) .
Illustration 5 g01250305
Turn valve (3) to the ON position.
Illustration 6 g01250304
Position sheet (2). Install bolts (1) .End By: Install the bottom guard. Refer to Disassembly and Assembly, " Bottom Guard - Remove and Install".
Start By:
Remove the bottom guard. Refer to Disassembly and Assembly, " Bottom Guard - Remove and Install".Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01250304
Remove bolts (1). Remove sheet (2) .
Illustration 2 g01250305
Turn valve (3) to the OFF position.
Illustration 3 g01250536
Disconnect hose assemblies (4) and (5) .
Remove bolts (6) and fuel transfer pump (7) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 4 g01250536
Position fuel transfer pump (7). Install bolts (6) .
Connect hose assemblies (5) and (4) .
Illustration 5 g01250305
Turn valve (3) to the ON position.
Illustration 6 g01250304
Position sheet (2). Install bolts (1) .End By: Install the bottom guard. Refer to Disassembly and Assembly, " Bottom Guard - Remove and Install".
Caterpillar parts catalog:
Parts eyebolt Caterpillar catalog:
0957033
EYEBOLT
307, 307B, 308C, 315, 315B, 315B FM L, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E120, E140, E70, E70B
307, 307B, 308C, 315, 315B, 315B FM L, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E120, E140, E70, E70B
1905912
EYEBOLT
311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
1905859
EYEBOLT
311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN, E110B, E120B, E200B
0859899
EYEBOLT
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN, E110B, E120B, E200B
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN, E110B, E120B, E200B
0859260
EYEBOLT
311, 311B, 312B, 320 L, 320B, E110, E110B, E120B, E200B
311, 311B, 312B, 320 L, 320B, E110, E110B, E120B, E200B
1S1596
EYEBOLT
988, G379
988, G379
2086781
EYEBOLT
CPT372
CPT372
2085153
EYEBOLT
CPT372
CPT372
4349935
EYEBOLT
WS223 SS, WSF223 SS, WSP273
WS223 SS, WSF223 SS, WSP273
651, 666, WS223 SS, WSF223 SS
2Y7623
EYEBOLT
3306, 3408B
3306, 3408B
0968784
EYEBOLT
313B
313B
0949421
EYEBOLT
307D, 308D, 313B
307D, 308D, 313B
0949742
EYEBOLT
307, 307B, 313B, E110, E450, E70, E70B
307, 307B, 313B, E110, E450, E70, E70B
0957033
EYEBOLT
307, 307B, 308C, 315, 315B, 315B FM L, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E120, E140, E70, E70B
307, 307B, 308C, 315, 315B, 315B FM L, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E120, E140, E70, E70B
8U7017
EYEBOLT
205B, 206B, 211B, 212B, M312, M315, M318, M320
205B, 206B, 211B, 212B, M312, M315, M318, M320
8T3220
EYEBOLT
350, CW-14, M312, M313C, M313D, M315, M315C, M315D, M316C, M316D, M318, M318C, M318D, M320, M322C, M322D, PS-150C, PS-200B
350, CW-14, M312, M313C, M313D, M315, M315C, M315D, M316C, M316D, M318, M318C, M318D, M320, M322C, M322D, PS-150C, PS-200B