2459344 FAN AS Caterpillar parts
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 321C, 321D LCR, 323D L, 323D LN, 323D SA
Rating:
Alternative (cross code) number:
CA2459344
245-9344
2459344
CA2459344
245-9344
2459344
Weight: 10 pounds 4 kg.
Information:
BLADE WIDTH
115
mm
BOLT CIRCLE DIAMETER
152.4
mm
DIAMETER OF PITCH CIRCLE HOLES
9
mm
HUB THICKNESS
3.2
mm
NUMBER OF BLADES
10
NUMBER OF PITCH HOLES
6
OD
732
mm
PILOT HOLE DIAMETER
127.04
mm
EXCAVATOR, MOBILE HYD POWER UNIT,
You can buy:
US$95.03
14 Jul 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Fan(s) Fits Caterpillar Replaces 2459344
Reliable Aftermarket Parts OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
Reliable Aftermarket Parts OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
RAParts 2459344 Fits Caterpillar Fan fits Several Models
Reliable Aftermarket Parts One New Aftermarket Replacement Fan That Fits Caterpillar Models. Replaces Part Number: Cso90-0045, || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
Reliable Aftermarket Parts One New Aftermarket Replacement Fan That Fits Caterpillar Models. Replaces Part Number: Cso90-0045, || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
CTP 2459344 Standard Fan for Models 320D/D2, 320D L, 320D LN, 323D, 323D L, 321D
CTP With the engine off, the ignition locked in the off position, and any required guarding removed, you are now ready to reverse your fan; There is a pink "DANGER" tag provided with your fan that should also be fastened to the ignition switch panel || Individually reverse each blade by simply pushing inward (towards the hub) to compress the spring and then begin to rotate the blade; it should only turn in one direction || Once the blade begins to rotate, you no longer need to keep pushing inward; continue to turn the blade toward the desired position; continue to reverse the remaining blades so that they are all in the same position || Once the blade is rotated fully to the desired position, the blade will "spring" outward and lock itself into place; Now the blade will not be able to be turned around without pushing it inward again; The reversing of one blade is now complete || Now that all of the blades have been reversed, the fan will force the air in the opposite direction. You are now ready to re-install the guarding, unlock the ignition switch, and continue operating the equipment with increased comfort
CTP With the engine off, the ignition locked in the off position, and any required guarding removed, you are now ready to reverse your fan; There is a pink "DANGER" tag provided with your fan that should also be fastened to the ignition switch panel || Individually reverse each blade by simply pushing inward (towards the hub) to compress the spring and then begin to rotate the blade; it should only turn in one direction || Once the blade begins to rotate, you no longer need to keep pushing inward; continue to turn the blade toward the desired position; continue to reverse the remaining blades so that they are all in the same position || Once the blade is rotated fully to the desired position, the blade will "spring" outward and lock itself into place; Now the blade will not be able to be turned around without pushing it inward again; The reversing of one blade is now complete || Now that all of the blades have been reversed, the fan will force the air in the opposite direction. You are now ready to re-install the guarding, unlock the ignition switch, and continue operating the equipment with increased comfort
This part in 2 request:
Show.
This information for suppliers only!
2023-06-02
2018-11-21
Compatible equipment models: 2459344:
Information:
Certain parameters are unique for each engine application. Table 1 is a list of the parameters that can be configured for G3500C/E Engines. The parameters are programmed into the Electronic Control Module (ECM) via the Caterpillar Electronic Technician (ET). The values of the parameters can be viewed on the "Configuration" screen of Cat ET.Refer to Systems Operation/Testing and Adjusting, "Electronic Control System Parameters" for the descriptions of the parameters.
Table 1
Configuration Parameters for G3500C and G3500E Engines
Timing Control
"First Desired Timing"
"Second Desired Timing"
Air/Fuel Ratio Control
"Fuel Quality Input Type Configuration"(1)
"Fuel Quality Sensor LHV Lower Limit"(1)
"Fuel Quality Sensor LHV Upper Limit"(1)
"Fuel Quality"
"Gas Specific Gravity"
"Fuel Specific Heat Ratio"
"Desired Emission Gain Adjustment Percentage"
"Air/Fuel Proportional Gain"
"Air/Fuel Integral Gain"
Speed Control
"Low Idle Speed"
"Minimum Engine High Idle Speed"
"Maximum Engine High Idle Speed"
"Engine Acceleration Rate"
"Desired Speed Input Configuration"
"Governor Type Setting"
"Engine Speed Droop"
"Governor Gain Factor"
"Governor Stability Factor"
"Governor Compensation Factor"
"Auxiliary Proportional Governor Gain 1"
"Auxiliary Integral Governor Gain 1"
"Auxiliary Derivative Governor Gain 1"
Start/Stop Control
"Driven Equipment Delay Time"
"Crank Terminate RPM"
"Engine Purge Cycle Time"
"Cooldown Duration"
"Cycle Crank Time"
"Engine Overcrank Time"
"Engine Speed Drop Time"
"Engine Pre-Lube Time Out Period"
Monitoring and Protection
"High Inlet Air Temp Engine Load Set Point"
"Impending Shutdown Delay Enable Status"
"Impending Shutdown Delay Time"
Power Monitoring
"Generator Output Power Sensor Scale Factor"
"Generator Output Power Sensor Offset"
"Engine Output Power"
"Engine Driven Accessory Load Configuration"
Information for the ECM
"Engine Serial Number"
"Equipment ID"
"Customer Password #1"
"Customer Password #2"
"Total Tattletale"
(1) This parameter applies to engines that are equipped with software that supports an input for variable fuel BTU.
Table 1
Configuration Parameters for G3500C and G3500E Engines
Timing Control
"First Desired Timing"
"Second Desired Timing"
Air/Fuel Ratio Control
"Fuel Quality Input Type Configuration"(1)
"Fuel Quality Sensor LHV Lower Limit"(1)
"Fuel Quality Sensor LHV Upper Limit"(1)
"Fuel Quality"
"Gas Specific Gravity"
"Fuel Specific Heat Ratio"
"Desired Emission Gain Adjustment Percentage"
"Air/Fuel Proportional Gain"
"Air/Fuel Integral Gain"
Speed Control
"Low Idle Speed"
"Minimum Engine High Idle Speed"
"Maximum Engine High Idle Speed"
"Engine Acceleration Rate"
"Desired Speed Input Configuration"
"Governor Type Setting"
"Engine Speed Droop"
"Governor Gain Factor"
"Governor Stability Factor"
"Governor Compensation Factor"
"Auxiliary Proportional Governor Gain 1"
"Auxiliary Integral Governor Gain 1"
"Auxiliary Derivative Governor Gain 1"
Start/Stop Control
"Driven Equipment Delay Time"
"Crank Terminate RPM"
"Engine Purge Cycle Time"
"Cooldown Duration"
"Cycle Crank Time"
"Engine Overcrank Time"
"Engine Speed Drop Time"
"Engine Pre-Lube Time Out Period"
Monitoring and Protection
"High Inlet Air Temp Engine Load Set Point"
"Impending Shutdown Delay Enable Status"
"Impending Shutdown Delay Time"
Power Monitoring
"Generator Output Power Sensor Scale Factor"
"Generator Output Power Sensor Offset"
"Engine Output Power"
"Engine Driven Accessory Load Configuration"
Information for the ECM
"Engine Serial Number"
"Equipment ID"
"Customer Password #1"
"Customer Password #2"
"Total Tattletale"
(1) This parameter applies to engines that are equipped with software that supports an input for variable fuel BTU.
Cat SIS web machinery list:
Parts fan Caterpillar catalog:
3244122
FAN GP-SUCTION
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 321D LCR, 323D L
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 321D LCR, 323D L
2797786
FAN GP-SUCTION
320D LRR, 321C
320D LRR, 321C
2792699
FAN AR-REVERSIBLE
320D, 320D FM
320D, 320D FM
3692257
FAN AR-SUCTION
320D GC, 320D L, 320D2, 320D2 GC, 323D L
320D GC, 320D L, 320D2, 320D2 GC, 323D L
3692248
FAN GP-SUCTION
320D GC, 320D L, 320D2, 320D2 GC, 323D L
320D GC, 320D L, 320D2, 320D2 GC, 323D L
3263957
FAN GP-SUCTION
320D, 320D FM
320D, 320D FM
1852639
FAN AS
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14H, 14H NA, 14M,...
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14H, 14H NA, 14M,...
1805316
FAN GP-CIRCULATING
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 307C, 307D, 311C, 312C L, 315C, 318C, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 324D FM, 324D FM LL, 325C, 325C FM, 325D FM...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 307C, 307D, 311C, 312C L, 315C, 318C, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 324D FM, 324D FM LL, 325C, 325C FM, 325D FM...
2459343
FAN AS
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 321D LCR, 323D L
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 321D LCR, 323D L
2441934
FAN GP
533, 543, HA770, HA771, HA870, HA871, TK370, TK371, TK380
533, 543, HA770, HA771, HA870, HA871, TK370, TK371, TK380
2275434
FAN AS
554, 564, 574B, 580B
554, 564, 574B, 580B
2040910
FAN AS
320C, 320C FM, 320C L, 321C, 330C, 330C FM, 330C L, 330C MH
320C, 320C FM, 320C L, 321C, 330C, 330C FM, 330C L, 330C MH
2112742
FAN AS
322C
322C
1665538
FAN AS
554, 574
554, 574
1665541
FAN AS
554
554
3845072
FAN AS
584
584
3845071
FAN GP
584
584
3516110
FAN
584
584
3644712
FAN AS
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C
3382947
FAN
2470C, 2570C, 2670C, 553C, 563C, 573C, 584
2470C, 2570C, 2670C, 553C, 563C, 573C, 584
2459343
FAN AS
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 321D LCR, 323D L
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 321D LCR, 323D L