3559948 FASTENER GP-CEM Caterpillar parts
CW-34
Rating:
Alternative (cross code) number:
CA3559948
355-9948
3559948
CA3559948
355-9948
3559948
PNEUMATIC COMPACTOR,
Compatible equipment models: 3559948:
Information:
Removal Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     140-7742     Protective Sleeve     4    
B     1U-8233     Nylon Lifting Sling     4    Start By:
Remove the hoist cylinders. Refer to Disassembly and Assembly, "Hoist Cylinder - Remove".
Remove the tailgate cylinder. See Disassembly and Assembly, "Tailgate Cylinder - Remove".
Personal injury or death can result from improper lifting or blocking.When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.
Note: This procedure is a typical example.
Illustration 1 g00578362
Illustration 2 g00578365
Remove bolts (1), the nuts, and the washers.
Disconnect the electrical connections for rear lights (2) .
Remove lights (2) .
Remove bolts (3), the nuts, and the washers .
Illustration 3 g00578366
Illustration 4 g00578367
Attach Tooling (A) to dump body (4). Attach Tooling (B) and an appropriate hoist. Apply sufficient tension to the lifting slings in order to relieve the pressure on pin assemblies (5) .
Use two 3/4 - 10 NC forcing screws (6) in order to remove pin assembly (5) .Note: If there are shims between the hoist pivot and the pivot bracket, note the location of the shims for assembly.
Repeat Step 6 for the opposite side of the dump body.
Remove dump body (4) from the machine. The weight of the dump body is 4357 kg (9606 lb).
Remove Tooling (A) and Tooling (B) from the dump body.
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     140-7742     Protective Sleeve     4    
B     1U-8233     Nylon Lifting Sling     4    Start By:
Remove the hoist cylinders. Refer to Disassembly and Assembly, "Hoist Cylinder - Remove".
Remove the tailgate cylinder. See Disassembly and Assembly, "Tailgate Cylinder - Remove".
Personal injury or death can result from improper lifting or blocking.When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.
Note: This procedure is a typical example.
Illustration 1 g00578362
Illustration 2 g00578365
Remove bolts (1), the nuts, and the washers.
Disconnect the electrical connections for rear lights (2) .
Remove lights (2) .
Remove bolts (3), the nuts, and the washers .
Illustration 3 g00578366
Illustration 4 g00578367
Attach Tooling (A) to dump body (4). Attach Tooling (B) and an appropriate hoist. Apply sufficient tension to the lifting slings in order to relieve the pressure on pin assemblies (5) .
Use two 3/4 - 10 NC forcing screws (6) in order to remove pin assembly (5) .Note: If there are shims between the hoist pivot and the pivot bracket, note the location of the shims for assembly.
Repeat Step 6 for the opposite side of the dump body.
Remove dump body (4) from the machine. The weight of the dump body is 4357 kg (9606 lb).
Remove Tooling (A) and Tooling (B) from the dump body.
Caterpillar SIS machinery equipment:
Caterpillar SIS
CW34 Pneumatic Compactor TLJ00001-UP (MACHINE) POWERED BY C4.4 Engine »
355-9948
FASTENER GP-CEM
CW34 Pneumatic Compactor CT300001-UP (MACHINE) POWERED BY C4.4 Engine »
355-9948
FASTENER GP-CEM
CW34 Pneumatic Compactor AL300001-UP (MACHINE) POWERED BY C4.4 Engine »
355-9948
FASTENER GP-CEM
320 GC Excavator KTN00001-UP (MACHINE) POWERED BY C4.4 Engine »
355-9948
FASTENER GP-CEM
320 & 320 GC Excavators XBJ00001-UP (MACHINE) POWERED BY C4.4 Engine »
355-9948
FASTENER GP-CEM
Caterpillar parts catalog:
Parts fastener Caterpillar catalog:
1563678
FASTENER GP-FLYWHEEL
3176C, 3196, C-10, C-12, C-9, C11, C13, C9, CX31-C13I, CX31-C9I, RM-300, TH31-E61, TH35-C11I, TH35-C13I
3176C, 3196, C-10, C-12, C-9, C11, C13, C9, CX31-C13I, CX31-C9I, RM-300, TH31-E61, TH35-C11I, TH35-C13I
2361823
FASTENER GP-ENGINE
3056E, CP-663E, CS-663E, CS-683E
3056E, CP-663E, CS-663E, CS-683E
2W3640
FASTENER GP-EXHAUST MANIFOLD
120G, 130G, 936, 950B, D5H
120G, 130G, 936, 950B, D5H
1N4579
FASTENER GP
120G, 130G, D4E
120G, 130G, D4E
1206629
FASTENER GP-OIL PAN
973, 973C
973, 973C
2446345
FASTENER GP-SWING & FINAL DR
330C, 330D L, 336D L
330C, 330D L, 336D L
3559939
FASTENER GP-CEM
CP-54B, CS-54B, CS-64B
CP-54B, CS-54B, CS-64B