AVSPARE.COM
parts catalog

FASTENER GP-FRONT HOUSING 5089041 - Caterpillar



5089041 FASTENER GP-FRONT HOUSING Caterpillar parts FASTENER
Rating:
36
Alternative (cross code) number:
CA5089041
508-9041
5089041
Caterpillar 5089041 FASTENER GP-FRONT HOUSING

Buy FASTENER GP-FRONT HOUSING 5089041 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:

1. Complete 10 and 50 Hour Services.2. Change engine oil and filter.3. Clean engine breather.4. Change hydraulic oil breather and suction filter elements.5. Check fan and alternator drive belts.Changing Engine Oil And Filter
With engine stopped and oil warm: 1. Remove the crankcase oil drain plug. Allow the oil to drain.2. Unscrew and remove the filter. Be sure the old filter gasket does not remain attached inside the filter base or leaking will occur between the new filter gasket and the old gasket.3. Wipe the filter base. 4. Apply a thin coat of clean oil to the gasket of the new filter.5. Install the new filter. Hand tighten the filter 1/2 to 3/4turn after the gasket contacts the filter base.6. Clean and install the drain plug.7. Fill the crankcase to the safe starting range on the ENGINE STOPPED side of the dipstick.8. Start the engine and check for oil leaks.9. After the engine is warm, check the oil level with the engine idling.10. If necessary, add oil to bring the oil level to the FULL mark on the ENGINE IDLING side of the dipstick.Cleaning Engine Breather
1. Release the hose clamp and disconnect the fumes disposal tube.2. Remove the breather assembly.3. Wash the breather in solvent.4. Allow to drain dry and then wipe. 5. Inspect the gasket. Install a new gasket if necessary.6. Install the breather.7. Connect the fumes disposal tube.Changing Hydraulic Oil Tank Breather Filter Element
The hydraulic oil tank air filter element is a spin-on type element. To change the element: 1. Unscrew the filter element from the filter head. Be sure the gasket comes off with the filter element.2. Coat the gasket of the new element with clean hydraulic oil.3. Screw the element onto the filter head until the gasket contacts the head.4. Turn the element about 1/2 turn more.Checking Drive Belts For Fan And Alternator
If one belt in a set requires replacement, always install a new matched set of belts, not just the worn belt. If only the worn belt is replaced, the new unstretched belt will be carrying all of the load and all the belts will fail in rapid succession. It is advisable to read just new belts after a short period of running to take up slack caused by the initial stretch.The fan and alternator belt tension can be checked by applying a 25 pound force perpendicular to the belt midway between the fan and alternator pulleys. Belt deflection should be 9/16" to 13/16".Changing Hydraulic Pump Suction Filter Elements
See pages 4-41 and 4-42.To adjust the tension of the fan and alternator belts: 1. Loosen the adjusting bolt in the slotted alternator bracket.2. Apply pressure to the alternator front housing only to move the alternator outward.3. When the desired belt tension is obtained, tighten the adjusting bolt.4. Recheck the belt tension. Adjust as necessary.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
DE18E3/DE22E3 Generator Set TY200001-UP POWERED BY C2.2 Engine
C2.2 Industrial Engine G7L00001-UP


Parts fastener Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.