AVSPARE.COM
parts catalog

FENDER ASSEM. (L.H.) 4V7332 - Caterpillar



4V7332 FENDER ASSEM. (L.H.) Caterpillar parts 966D FENDER
Rating:
62
Alternative (cross code) number:
CA4V7332
4V-7332
4V7332
Caterpillar 4V7332 FENDER ASSEM. (L.H.)
Weight: 88 pounds 40 kg.

Buy FENDER ASSEM. (L.H.) 4V7332 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 4V7332:

WHEEL LOADER  966D   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:


Illustration 1 g02075095
Schematic of the +5 Volt Sensor DC Power Supply from the Machine ECMThis diagnostic code is associated with the Machine ECM 5 Volt DC Sensor Power Supply. The 5 v sensor power supply provides power to the Counterbalance Pressure Sender.The CID 0262 FMI 04 diagnostic code is activated when the Machine ECM detects that the voltage of the 5 v power supply circuit is lower than normal.Note: The Machine ECM is located inside the Center Console.The following conditions could cause this diagnostic code:
The power supply circuit is shorted to a ground source.
The ECM has failed. This situation is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Clear the diagnostic codes when the problem has been corrected. Verify that the CID 0262 FMI 04 is active before performing this procedure.System Response:Components connected to the controller will not log faults.Test Step 1. CHECK THE POWER SUPPLY AT THE MACHINE ECM
Turn the disconnect switch and the key start switch to the OFF position.
At the Machine ECM connector J1, remove the +5V supply socket at contact J1-11. Remove the return socket at contact J1-21. The Machine ECM Harness connector J1 remains connected to the ECM.
Turn the disconnect switch and the key switch to the ON position.
Use the multimeter probes in order to make contact on the Machine ECM connector pins. Measure the voltage at the ECM between the power supply contact J1-11 and the return contact J1-21.Expected Result:The voltage measurement is 5.0 0.4 DCV.Results:
OK - The voltage measurement is 5.0 0.4 DCV. The voltage is correct. The ECM power supply is correct. Turn the key start switch and the disconnect switch to the OFF position. Install the wires and sockets that were removed from the J1 connector back into the original locations. Proceed to Test Step 2.
NOT OK - The voltage measurement is not 5.0 0.4 DCV. The ECM power supply is not correct.Repair: Prior to replacing an ECM, always contact the Technical Communicator for your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to Troubleshooting, "Electronic Control Module (ECM) - Replace".STOPTest Step 2. CHECK THE STATUS OF THE DIAGNOSTIC CODE
Inspect the harness connectors. Clean the contacts for the harness connectors. Check all wires for damage from chafing, corrosion, or excessive heat.
Reconnect all harness connectors. Make sure that the connectors are fully seated and the clips for each connector are fastened.
Turn the disconnect switch and the key switch to the ON position.
Operate the machine.
Determine if the CID 0262 FMI 04 diagnostic code is active.Expected Result:The CID 0262 FMI 04 diagnostic code

Caterpillar parts catalog:

Caterpillar parts catalog
966D WHEEL LOADER 94X00001-06488 (MACHINE) POWERED BY 3306 ENGINE
966D LOADER 99Y00001-05314 (MACHINE) POWERED BY 3306 ENGINE
966D WHEEL LOADER 35S00001-02074 (MACHINE) POWERED BY 3306 ENGINE


Parts fender Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.