AVSPARE.COM
parts catalog

FENDER ASSEM. (rear L.H.) 5V3405 - Caterpillar



5V3405 FENDER ASSEM. (rear L.H.) Caterpillar parts 950 FENDER
Rating:
57
Alternative (cross code) number:
CA5V3405
5V-3405
5V3405
Caterpillar 5V3405 FENDER ASSEM. (rear L.H.)
Weight: 0.60 pounds 0 kg.

Buy FENDER ASSEM. (rear L.H.) 5V3405 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 5V3405:

WHEEL LOADER  950   Caterpillar
Number on catalog scheme: None
 
  For full view, you need register

Information:


Illustration 1 g02160296
Schematic for Machine ECM Electrical System VoltageThis diagnostic code is recorded when the Machine ECM reads the electrical system voltage that is at contact J1-31 (wire 149-PU) as being below normal range (less than 18 v for 2 seconds).Note: The Machine ECM is located inside the Center Console.The possible causes of this diagnostic code are listed:
A charging system component has failed.
The ECM has failed. This situation is unlikely.This diagnostic code causes the implements to be inoperative because the voltage is too low in order to energize the solenoids.Ensure that CID 0168 FMI F01 is active. The "SERV CODE" indicator on the Caterpillar Monitoring System is illuminated.System Response:Components connected to the controller will not log faults. Machine may become inoperable.Test Step 1. CHECK THE BATTERY VOLTAGE.
Measure the voltage at the battery posts.Expected Result:The voltage is greater than 18 VDC.Results:
YES - The voltage is greater than 18 DCV. This situation should not cause the diagnostic code. Proceed to test step 2.
NO - The voltage is less than 18 DCV. The charging system is not correct. Repair: Check the charging system. See Special Instruction, REHS0354, "Charging System Troubleshooting". STOPTest Step 2. CHECK THE SYSTEM VOLTAGE
Disconnect the machine harness from the ECM.
Turn the disconnect switch and the key start switch to the ON position.
At machine harness connector J1 for the ECM, measure the voltage between contact J1-31 (wire 149-PU) and contact J1-23 (wire 200-BK).Expected Result:The voltage measures battery voltage.Results:
YES - The voltage is greater 18 DCV. This situation should not cause the diagnostic code. Repair: Inspect connector J1. Connect the machine harness to the ECM. If the CID 0168 FMI F01 remains present, check the charging system. See Special Instruction, REHS0354, "Charging System Troubleshooting". If the cause of the diagnostic code is not found, the ECM may have failed. Exit this procedure and perform this entire procedure again. Prior to replacing an ECM, always contact the Technical Communicator from your dealer for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to Troubleshooting, "Electronic Control Module (ECM) - Replace".STOP
NO - The voltage is less than 18 DCV. The machine harness has failed. Repair: Check the +battery circuit and the ground circuit in the machine harness. Repair the machine harness or replace the machine harness. STOP

Caterpillar parts catalog:

Caterpillar parts catalog
950 WHEEL LOADER 43J06268-UP (MACHINE) POWERED BY 3304 ENGINE


Parts fender Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.