AVSPARE.COM
parts catalog

FENDER ASSEM. (rear R.H.) 5V3430 - Caterpillar



5V3430 FENDER ASSEM. (rear R.H.) Caterpillar parts 950 FENDER
Rating:
56
Alternative (cross code) number:
CA5V3430
5V-3430
5V3430
Caterpillar 5V3430 FENDER ASSEM. (rear R.H.)
Weight: 0.05 pounds 0 kg.

Buy FENDER ASSEM. (rear R.H.) 5V3430 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 5V3430:

WHEEL LOADER  950   Caterpillar
Number on catalog scheme: 20
 
  For full view, you need register

Information:


Illustration 1 g02068536
Schematic for the Steering Angle SensorThis diagnostic code is associated with the Steering Angle Sensor (Steering Cylinder Linear Sensor). The FMI 04 means that the Machine ECM has determined that the voltage of the circuit for the position sensor is below normal. Note: The Machine ECM is located in the Center Console.The output frequency of the position sensor is approximately 500 hz. The duty cycle of the signal changes as the position sensor moves. The duty cycle varies from 5 to 95 percent.The possible causes of this diagnostic code are listed below:
The signal circuit for the sensor is shorted to ground.
The sensor has failed.
The Machine ECM has failed. This situation is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0163 FMI 04 is active before performing this procedure. Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.Test Step 1. CHECK THE SENSOR
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic code is active.
Observe the status of the diagnostic code. Disconnect the sensor from the machine harness.Expected Result:The CID 0163 FMI 04 remains active. The FMI has not changed and the "04" is still active.Results:
OK - The diagnostic code remains active. The sensor is correct. Proceed to Test Step 2.
NOT OK - The diagnostic code is no longer active. The sensor has failed.Repair: Replace the sensor.STOPTest Step 2. CHECK THE WIRING HARNESS OF THE SENSOR FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the sensor.
Disconnect the machine harness connectors from the Machine ECM.
At the machine harness connector for the Machine ECM, measure the resistance from the signal contact J2-41 (wire H765-WH) of the machine harness to all possible sources of ground. Measure the resistance to all contacts of the machine harness connectors for the Machine ECM.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - A resistance measurement is not correct. There is a short in the machine harness. Repair: The short is between signal contact J2-41 (wire H765-WH) and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts of the harness connectors and clean the contacts.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 0163 FMI 04.Expected Result:The CID 0163 FMI 04 is active. Results:
YES - The CID 0163 FMI 04 is active. The diagnostic code has not been corrected. The Machine ECM may have failed.Repair: Failure of the Machine ECM is unlikely. Exit the procedure and perform this procedure again. If the cause

Caterpillar parts catalog:

Caterpillar parts catalog
950 WHEEL LOADER 43J06268-UP (MACHINE) POWERED BY 3304 ENGINE


Parts fender Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.