AVSPARE.COM
parts catalog

FENDER ASSEM. (rear R.H.) 5V8218 - Caterpillar



5V8218 FENDER ASSEM. (rear R.H.) Caterpillar parts 966C FENDER
Rating:
24
Alternative (cross code) number:
CA5V8218
5V-8218
5V8218
Caterpillar 5V8218 FENDER ASSEM. (rear R.H.)
Weight: 21 pounds 9 kg.

Buy FENDER ASSEM. (rear R.H.) 5V8218 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 5V8218:

WHEEL LOADER  966C   Caterpillar
Number on catalog scheme: 20
 
  For full view, you need register

Information:


Illustration 1 g02069273
Schematic of the Cat Data Link CircuitThis failure results in codes that are logged against an ECM that is not communicating some expected information to the Implement (Screed) ECM. The Implement (Screed) ECM cannot communicate with the Engine ECM or the ECM appears to work intermittently. System Response:When this diagnostic code is active, the following occurs:
Engine shutdown due to diagnostic feature is disabled.
Loss of engine data over Cat Data Link.
Operator station fault lamp is active.
The following pop-up message shows on graphical display: "Loss of communication with Engine. Engine features may be disabled."Note: The Implement (Screed) ECM is located under the Screed Platform.Test Step 1. VERIFY THE HARDWARE AND THE SOFTWARE PART NUMBERS.
Verify that the following information is correct:
The part number of the software for the Implement (Screed) ECM
The part number of the "Engine ECM software"
The part number of the Implement (Screed) ECM
The part number of the Engine ECMNote: Consult the Business Unit that produces the product for the correct part numbers of the configuration software. Expected Result:All part numbers are correct. Results:
OK - All part numbers are correct. Proceed to test step 2.
NOT OK - All part numbers are NOT correct. The part number of the Implement (Screed) ECM may be incorrect. The part number of the Engine ECM may be incorrect. The incorrect software for the ECM may also be installed. Repair: Replace the incorrect ECM with an ECM that has the correct part number. Flash the correct and most current software. See Troubleshooting, "Electronic Control Module (ECM) - Flash Program".STOPTest Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the disconnect switch to the OFF position.
Inspect all harness connections that are related to the Cat Data Link. Make sure that the connectors are clean and tight.
Check the connectors for proper mating.
Check the wires at the connector.
Check each wire for nicks or signs of abrasion in the insulation.
Check for moisture at the connector.
Check the connectors for dirty contacts or corroded contacts.
Check each pin and each socket of the machine harness connectors. Expected Result:The machine harness connectors are tight and free of corrosion. Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to test step 3.
NOT OK - The machine harness connectors are in need of repair.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK FOR SHORTS TO GROUND.
The disconnect switch remains in the OFF position.
Disconnect the machine harness from all electronic control modules that use the Cat Data Link.
At the machine harness for the Implement (Screed) ECM, measure the resistance between frame ground and connector contact J1-10 (wire 944-OR) of the Cat Data Link circuit.
At the machine harness for the Implement (Screed) ECM, measure the resistance between frame ground and connector contact J1-20 (wire 945-BR) of the Cat Data Link circuit. Expected Result:The resistances are greater than 5 ohms. Results:
OK - The resistances are greater than 5000 ohms. The harness circuit resistance is correct. Proceed to test step 4.
NOT OK - Any resistance is less than 5000 ohms. The

Caterpillar parts catalog:

Caterpillar parts catalog
966 WHEEL LOADER - 42J06498-UP (MACHINE) POWERED BY 3306 ENGINE


Parts fender Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.