7K9186 FERRULE Caterpillar parts
518, 528, 941, 951B, 955K, 955L, D4D, D5, FB518
Rating:
Alternative (cross code) number:
CA7K9186
7K-9186
7K9186
CA7K9186
7K-9186
7K9186
Weight: 0.01 pounds 0 kg.
FELLER BUNCHER, WHEEL SKIDDER,
Compatible equipment models: 7K9186:
Number on catalog scheme:
6
For full view, you need register
Information:
Raise the temperature of bearing cone (22). Install bearing cone (22). Repeat this step for the remaining bearing cone.
Illustration 3 g06244453
Install ring seal (21).
Illustration 4 g06244435
Install pump drive gear (20).
Illustration 5 g06244206
Install the O-ring seal onto speed sensor (19). Install speed sensor (19).
Install bolt (18). Tighten bolt (18) to a torque of 14 3 N m (124 26.5 lb in)
Illustration 6 g06244481
Lower the temperature of bearing cup (17). Install bearing cup (17). Install the cover plate.
Illustration 7 g06244061
Install O-ring seal (16). Install bearing race (15).
Illustration 8 g06245552
Install pump adapter (14).
Install bolts (13). Tighten bolts (13) to a torque of 55 10 N m (41 7.4 lb ft).
Install Tooling (A). Use suitable lifting device to reposition torque converter housing (3) 180 degrees. The weight of the torque converter housing (3) is approximately 104 kg (230 lb).
Illustration 9 g06245561Note: Typical Example.
Use Tooling (B) to measure the end play of pump drive gear (20). The end play measurement must be 0.10 to 0.20 mm (0.004 to 0.008 inch). Add or remove shims in order to obtain the correct end play.
Repeat steps for the remaining pump drive gear.
Illustration 10 g06243781
Install bearing assembly (12).
Install idler gear assembly (11).
Illustration 11 g06244917
Lower the temperature of idler shaft (10). Install idler shaft (10).
Install bolt (9).
Illustration 12 g06244467
Install retaining rings (8) on the gear assembly.
Illustration 13 g06244466
Lower the temperature of bearing cup (7). Install bearing cup (7). Install bearing cone (6). Repeat this step for the opposite side.
Illustration 14 g06243494
Install gear assembly (5).
Install retaining ring (4).
Illustration 15 g06245324
Illustration 16 g06245240
Use Tooling (C) and a suitable lifting device to position bearing cage assembly (2). The weight of bearing cage assembly (2) is approximately 38 kg (84 lb).
Install bolts (1).End By:
Install the pump drive. Refer to Disassembly and Assembly, "Pump Drive - Install".
Cat SIS web machinery list:
Parts ferrule Caterpillar catalog:
12E, 14E, 16, 1673, 1673C, 1674, 1676, 1693, 16G, 24H, 3116, 3304, 3306, 3406, 3406B, 3406C, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3508B, 3512B, 3516B, 5110B, 561B, 561C, 589, 594, 621...
1673C, 1693, 3306, 3408, 3408C, 3412, 3412C, 3412D, 518, 589, 621R, 631C, 631E, 637D, 637E, 651E, 657E, 769C, 771C, 773B, 775B, 824B, 834B, 941, 950, 951B, 966C, 988B, 988F, 990, 992C, 992D, D10N, D34...
8S5210
FERRULE
561C, 594, 824B, 825B, 977K, 983, 988, 992, D5, D6C, D7F, D8H, D9G
561C, 594, 824B, 825B, 977K, 983, 988, 992, D5, D6C, D7F, D8H, D9G
1S4917
FERRULE
583H, 594, 824, 834, 950, 966C, 977H, 977K, 988, D5, D6C, D8H, D9G
583H, 594, 824, 834, 950, 966C, 977H, 977K, 988, D5, D6C, D8H, D9G
1S9301
FERRULE
12E, 824, 955H, 977H, D320A
12E, 824, 955H, 977H, D320A
9H4928
FERRULE
D320A
D320A
7H3896
FERRULE
D342, D353C, D379, D398, G379
D342, D353C, D379, D398, G379
3H3265
FERRULE
D342
D342
527, D5N, D6H, D6R, D6T
1186275
FERRULE - 7/8 in. (22 mm) WIRE ROPE
527, 561M, D5H, D5N, D6H, D6M, D6R, D6T
527, 561M, D5H, D5N, D6H, D6M, D6R, D6T
515, 525, 525B, 525C, 527, 535B, 535C, 545, 545C, 561M, D5H, D5M, D5N, D6H, D6M, D6N, D6R, D6T
1S4916
FERRULE
824, 834, 977H, 977K, 988, D8H
824, 834, 977H, 977K, 988, D8H
6B7750
FERRULE
561B, 977D
561B, 977D
4N0240
FERRULE
943
943