AVSPARE.COM
parts catalog

FILM-WARNING 3237256 - Caterpillar



3237256 FILM-WARNING Caterpillar parts FILM
Rating:
16
Alternative (cross code) number:
CA3237256
323-7256
3237256
Caterpillar 3237256 FILM-WARNING
Weight: 0.01 pounds 0 kg.

Buy FILM-WARNING 3237256 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 11
 
  For full view, you need register

Information:


Illustration 50 g00522519
Illustration 51 g00522517
Screw the coils of spring pair (14) onto spring seat assembly (15). Align the springs so that the springs are even with the spring seat and each other.
Illustration 52 g00522516
Slide spring seat assembly (15) onto the riser shaft with the springs toward the outside.Note: Rotate the springs on the spring seat so that the inner spring is aligned with the outer spring. Remove the sharp edges from the flat surface on the inside diameter of the springs. This will ensure that the springs are seated properly on the spring seat.
Illustration 53 g00522514
Install shims (13) for the governor high idle, if necessary.
Illustration 54 g00522509
Install shims (8) and spacer (11) onto rear spring seat (9) .
Illustration 55 g00521803
Install governor spring seat assembly (9) onto the riser shaft.
Illustration 56 g00521802
Remove O-ring seal (7). Lightly lubricate the bore of the governor rear housing with clean engine oil and loosely install cover (6). Drain the oil from the rear sump cover into a suitable container for storage or disposal.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 57 g00521801
Put cover assembly (6) in position on the governor. Install three bolts (1) and evenly tighten the bolts.
Ensure that orifice (2) for the dashpot is not plugged. Also ensure that orifice (2) is tight in the casting.
Illustration 58 g00521800
Install O-ring seal (3) onto cover (5) .
Illustration 59 g00521798
Put cover (5) in position on cover assembly (6) and install three bolts (4) .Note: Before performing Step 57, the low idle screw must be backed out completely so that the throttle lever contacts the governor housing. The low idle adjustment is made during governor calibration.
Illustration 60 g00565297
(M) 1U-7308 Shim Adjustment Tool
Install the 1U-7308 Shim Adjustment Tool (Tool (M) ) and put the dial indicator point on the center of the rear cover. Push down on the rear cover until the cover makes contact with the governor housing. Zero the dial indicator. Slowly release the pressure on the rear cover. As the cover is pushed out by the force of the spring under the cover, rotate the cover for approximately 90 degrees. The reading on the dial indicator will determine the amount of preload on the spring. Add shims or remove shims in order to establish the proper preload on the spring. Refer to the Technical Marketing Information (TMI) for the governor spring preload dimension according to the governor group number.Note: The rear cover assembly must move freely.Note: The preload dimension that is stated in the TMI should only be used for reference. The manufacturer of the governor is not required to meet the specification. The number of governor spring shims is determined by the governor test bench calibration. Governor spring shims are added in order to increase the tension on the high idle screw. Governor spring shims are removed in order to meet the function of low idle lug specification. If you are rebuilding the governor, the

Cat SIS web machinery list:

Caterpillar parts catalog
TH3510D Telehandler TH200001-UP (MACHINE) POWERED BY C3.4B or C4.4 Engine
TH306D Telehandler TD200001-UP (MACHINE) POWERED BY 3.6L Engine
TH514D Telehandler MWG00001-UP (MACHINE) POWERED BY C3.4B, C4.4 Engine
TH408D Telehandler TH400001-UP (MACHINE) POWERED BY C4.4 or C3.4 Engine
TH357D Telehandler TD600001-UP (MACHINE) POWERED BY C3.4 or C4.4 Engine
TH417D & TH314D Telehandler MKY00001-UP (MACHINE) POWERED BY 3.6 Engine
TH255C Telehandler JK201000-UP (MACHINE) POWERED BY 2.9 Engine
TH514C, TH417C, TH407C, TH414C, TH406C, TH337C, TH336C, Telehandler Transmission DJB00001-00483 (MACHINE)
TH336C Telehandler MJR00271-UP (MACHINE)
TH406C Telehandler GAT00258-UP (MACHINE)
TH337C Telehandler DJB00484-UP (MACHINE)
TH407C Telehandler JJT00172-UP (MACHINE)
TH414C Telehandler KEK00373-UP (MACHINE)
TH417C Telehandler RRJ00246-UP (MACHINE)
TH514C Telehandler KKW00177-UP (MACHINE)
TH514D Telehandler MWG00001-UP (MACHINE) POWERED BY C3.4B, C4.4 Engine
TH417C GC Telehandler NAB00001-UP (MACHINE) POWERED BY 3.6 Engine
TH414C GC Telehandler KRF00001-UP (MACHINE) POWERED BY 3.6 Engine


Parts film Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.