2699104 FILTER Caterpillar parts
301.6C, 302.5C
Rating:
Alternative (cross code) number:
CA2699104
269-9104
2699104
CA2699104
269-9104
2699104
Weight: 0.11 pounds 0 kg.
MINI HYD EXCAVATOR,
Number on catalog scheme:
5
For full view, you need register
Information:
the following repair:
Repair the faulty wiring or replace the faulty wiring.
Reconnect the 31-pin connector. Use the electronic service tool to clear all logged diagnostic codes.
Start the engine. Use the electronic service tool to check for an active 3427-5 diagnostic code.
Use the "Aftertreatment Fuel Pump Override" in the electronic service tool to activate the ARD fuel pump. Check for an active 3427-6 diagnostic code.
Confirm that the fault has been eliminated.STOP
A 3427-6 diagnostic code is still active with the jumper installed. - Proceed to Test Step 7.Test Step 7. Bypass the Engine Harness
Turn the keyswitch to the OFF position.
Disconnect the P2 connector.
Inspect the P2/J2 connector. Refer to Troubleshooting, "Electrical Connectors - Inspect"
Remove the wires from P2:41 and P2:42.
Remove the wires from socket 26 and socket 19 on the 31-pin connector on the engine harness.
Fabricate two jumper wires that are long enough to reach from the ECM to the 31-pin connector.
Insert one end of a jumper into P2:41. Insert the other end of the jumper into socket 19 on the 31-pin connector on the engine harness.
Insert one end of the other jumper into P2:42. Insert the other end of the jumper into socket 26 on the 31-pin connector on the engine harness.
Reconnect the P2 connector. Reconnect the 31-pin connector.
Start the engine. Use the electronic service tool to check for an active 3427-5 diagnostic code.
Use the "Aftertreatment Fuel Pump Override" in the electronic service tool to activate the ARD fuel pump. Check for an active 3427-6 diagnostic code.
Stop the engine.
Disconnect the P2/J2 connector. Disconnect the 31-pin connector.
Remove the jumper wire.Results:
OK - There are no active 3427 diagnostic codes at this time. The fault is in the engine harness between the ECM and the 31-pin connector.Repair: Perform the following repair:
Repair the faulty wiring or replace the faulty wiring.
Reconnect the P2/J2 connector. Reconnect the 31-pin connector.
Start the engine. Use the electronic service tool to check for an active 3427-5 diagnostic code.
Use the "Aftertreatment Fuel Pump Override" in the electronic service tool to activate the ARD fuel pump. Check for an active 3427-6 diagnostic code.
Confirm that the fault has been eliminated.STOP
Not OK - A 3427 diagnostic code is still active at this time. Return all wires to the original configuration and proceed to Test Step 8.Test Step 8. Check the ECM
Make sure that the latest flash file for the application is installed in the ECM. Refer to Troubleshooting, "Flash Programming".
Contact the Technical Communicator at a Cat dealer.Note: This consultation can greatly reduce the repair time.
If the Technical Communicator recommends the use of a test ECM, install a test ECM. Refer to Troubleshooting, "Replacing the ECM".
Use the electronic service tool in order to clear all logged diagnostic codes.
Start the engine.
Use the "Aftertreatment Fuel Pump Override" in the electronic service tool to activate the ARD fuel pump. Check for active diagnostic codes.
Use the "Aftertreatment Fuel Pump Override" in the electronic service tool to deactivate the ARD fuel pump. Check for active diagnostic codes.Results:
There are no active 3427 diagnostic codes - The replacement ECM functions correctly.Repair: Perform the
Repair the faulty wiring or replace the faulty wiring.
Reconnect the 31-pin connector. Use the electronic service tool to clear all logged diagnostic codes.
Start the engine. Use the electronic service tool to check for an active 3427-5 diagnostic code.
Use the "Aftertreatment Fuel Pump Override" in the electronic service tool to activate the ARD fuel pump. Check for an active 3427-6 diagnostic code.
Confirm that the fault has been eliminated.STOP
A 3427-6 diagnostic code is still active with the jumper installed. - Proceed to Test Step 7.Test Step 7. Bypass the Engine Harness
Turn the keyswitch to the OFF position.
Disconnect the P2 connector.
Inspect the P2/J2 connector. Refer to Troubleshooting, "Electrical Connectors - Inspect"
Remove the wires from P2:41 and P2:42.
Remove the wires from socket 26 and socket 19 on the 31-pin connector on the engine harness.
Fabricate two jumper wires that are long enough to reach from the ECM to the 31-pin connector.
Insert one end of a jumper into P2:41. Insert the other end of the jumper into socket 19 on the 31-pin connector on the engine harness.
Insert one end of the other jumper into P2:42. Insert the other end of the jumper into socket 26 on the 31-pin connector on the engine harness.
Reconnect the P2 connector. Reconnect the 31-pin connector.
Start the engine. Use the electronic service tool to check for an active 3427-5 diagnostic code.
Use the "Aftertreatment Fuel Pump Override" in the electronic service tool to activate the ARD fuel pump. Check for an active 3427-6 diagnostic code.
Stop the engine.
Disconnect the P2/J2 connector. Disconnect the 31-pin connector.
Remove the jumper wire.Results:
OK - There are no active 3427 diagnostic codes at this time. The fault is in the engine harness between the ECM and the 31-pin connector.Repair: Perform the following repair:
Repair the faulty wiring or replace the faulty wiring.
Reconnect the P2/J2 connector. Reconnect the 31-pin connector.
Start the engine. Use the electronic service tool to check for an active 3427-5 diagnostic code.
Use the "Aftertreatment Fuel Pump Override" in the electronic service tool to activate the ARD fuel pump. Check for an active 3427-6 diagnostic code.
Confirm that the fault has been eliminated.STOP
Not OK - A 3427 diagnostic code is still active at this time. Return all wires to the original configuration and proceed to Test Step 8.Test Step 8. Check the ECM
Make sure that the latest flash file for the application is installed in the ECM. Refer to Troubleshooting, "Flash Programming".
Contact the Technical Communicator at a Cat dealer.Note: This consultation can greatly reduce the repair time.
If the Technical Communicator recommends the use of a test ECM, install a test ECM. Refer to Troubleshooting, "Replacing the ECM".
Use the electronic service tool in order to clear all logged diagnostic codes.
Start the engine.
Use the "Aftertreatment Fuel Pump Override" in the electronic service tool to activate the ARD fuel pump. Check for active diagnostic codes.
Use the "Aftertreatment Fuel Pump Override" in the electronic service tool to deactivate the ARD fuel pump. Check for active diagnostic codes.Results:
There are no active 3427 diagnostic codes - The replacement ECM functions correctly.Repair: Perform the
Caterpillar parts catalog:
Parts filter Caterpillar catalog:
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 301.5, 301.6C, 301.7D, 301.7D CR, 302.2D, 302.4D, 302.5, 302.5C, 302.7D, 303.5, 303.5C, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304...
2414083
FILTER GP-OIL
301.6C, 302.5C
301.6C, 302.5C
2430249
FILTER GP-CAB AIR
301.6C
301.6C
2430250
FILTER GP-CAB AIR
302.5C
302.5C
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 301.5, 301.6C, 301.7D, 301.7D CR, 302.2D, 302.4D, 302.5, 302.5C, 302.7D, 303.5, 303.5C, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304...
302.5C, C3.3
302.5C, C3.3
301.5, 301.6C
302.5C, 303, 304
300.9D, 301.4C, 301.6C, 301.7D, 302.2D, 302.4D, 302.7D, CB-14, PS-150B, PS-150C, PS-200B, PS-360B
301.6C, 302.5C
3196268
FILTER GP-OIL
301.6C
301.6C
301.6C, 302.5C
300.9D, 301.4C, 301.6C, 301.7D, 302.2D, 302.4D, 302.7D, CB-14, PS-150B, PS-150C, PS-200B, PS-360B
303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E
307D, 320D, 320D FM, 320D L, 323D L, 330D, 336D L, 365C, 365C L, 385C, 385C L, M313D, M315D, M316D, M318D, M318D MH, M322D, M322D MH, M325D L MH, M325D MH
307D, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR,...
307D, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR,...
304C CR, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 307E, 308E, 308E CR, 308E SR
304C CR, 305.5D, 305.5E, 305C CR