AVSPARE.COM
parts catalog

FILTER ELEMENT-AIR 5088563 - Caterpillar



5088563 FILTER ELEMENT-AIR Caterpillar parts FILTER
Rating:
16
Alternative (cross code) number:
CA5088563
508-8563
5088563
Caterpillar 5088563 FILTER ELEMENT-AIR
Weight: 1 pounds 0 kg.

Buy FILTER ELEMENT-AIR 5088563 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 6
 
  For full view, you need register

Information:

NOTE C: To verify overspeed shutdown system operation, push in for a moment the verify push button. The engine must shut down at 75% or more of overspeed setting.NOTE D: Input voltage: Maximum 37 VDC Minimum 8 VDC.NOTE E: The engine overspeed setting rpm is 118% of rated engine rpm.NOTE F: The magnetic pick-up frequency (HZ) at the overspeed or cranking termination setting is calculated with the formula that follows: If the rated speed of the engine is other than shown in the chart, the magnetic pick-up frequency for the overspeed setting can be found according to NOTES E and F.If a 2301 Governor is used, only one magnetic pick-up is needed. Use the magnetic pick-up from the overspeed group. Connect the wires from the magnetic pick-up to the overspeed switch and then connect wires from the speed switch to the 2301 Governor. The overspeed switch can be installed close to the 2301 Governor if needed.To reset overspeed switch, push in reset button for a moment.Power Takeoff Clutches
Clutch Adjustment
POWER TAKEOFF CLUTCH (Typical Illustration)1. Disconnect linkage (if so equipped) from the clutch lever. Fasten a spring scale to the clutch lever at the distance, from the lever shaft center, shown in the chart.2. Look at the spring scale. Keep the angle between the scale and the lever at 90°. Pull the lever with the spring scale until the clutch engages. Make reference to the chart to find the correct amount of pull for the clutch assembly. 3. If the pull needed to engage the clutch is not correct, make an adjustment as follows: 4. Remove the inspection plate from the clutch housing.5. Turn the clutch until lock pin (1 or 2) can be seen.6. Release push type lock pin (1) or pull type lock pin (2). Turn the adjustment ring and check the pull needed to engage the clutch again. Turn the adjustment ring clockwise, as seen from the rear of the clutch, to increase the pull needed. Turn it counterclockwise to decrease the pull needed.
CLUTCH ADJUSTMENT
1. Lock pin (push type). 2. Lock pin (pull type).Assembly Adjustments
End Play For Shaft Bearings
1. With dry bearings installed on the shaft install the shaft in the housing.2. Install the retainer. Tighten the retainer (nut or shim type) until 60 lb. in. (6.8 N m) is needed to keep the shaft in rotation.3. With shim type retainer measure the space between the retainer and the carrier. Add .013 in. (0.33 mm) to this measurement. Install this amount of shims between the retainer and the carrier. With nut type retainers turn it out the number of notches shown on the chart.4. Hit the output end of the clutch shaft with a soft hammer. This will cause the front bearing cup to move against the retainer. 5. Check the shaft end play with a dial indicator. If necessary add or subtract shims; or turn nut to get the correct end play.Hub Nut Installation
1. Tighten the hub nut to a torque of 30 lb. ft.

Caterpillar parts catalog:

Caterpillar parts catalog
R1300G Underground Mining LJB00001-UP (MACHINE) POWERED BY 3306 Engine
R1300G Series II Load Haul Dump RSL00001-UP (MACHINE) POWERED BY C6.6 Engine
R2900G Load Haul Dump JLK00001-UP (MACHINE) POWERED BY C15 Engine
R1700G Load Haul Dump SBR00001-UP (MACHINE) POWERED BY C11 Engine
R1600G Load Haul Dump 9YZ00001-UP (MACHINE) POWERED BY 3176C Engine
R1300G Load Haul Dump NJB00001-UP (MACHINE) POWERED BY 3306 Engine
R1700G Load Haul Dump XBR00001-UP (MACHINE) POWERED BY C11 Engine
AD55 Underground Articulated Truck DNW00001-UP (MACHINE) POWERED BY C18 Engine
AD45B Underground Articulated Truck CXM00001-UP (MACHINE) POWERED BY C18 Engine
AD30 Underground Articulated Truck DXR00001-UP (MACHINE) POWERED BY C15 Engine
AD55B Underground Articulated Truck JNW00001-UP (MACHINE) POWERED BY C27 Engine


Parts filter Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.