7W5495 FILTER ELEMENT AS-AIR Caterpillar parts
16G, 3306, 3306B, 578, 621E, 623B, 623E, 627E, 75, 824C, 826C, 963, 973, 980C, 980F, D25D, D300D, D40D, D6D, D8N, G3306, G3406
Rating:
Alternative (cross code) number:
CA7W5495
7W-5495
7W5495
CA7W5495
7W-5495
7W5495
Weight: 4 pounds 2 kg.
Information:
EFFECTIVE FILTER AREA
8.76
mm2
LENGTH
342.9
mm
MAJOR OD
292.1
mm
MINOR OD
283
mm
TYPE
000000000001
ARTICULATED TRUCK, WHEEL TRACTOR,
Cross Reference:
CATERPILLAR
1P-7716,
7W-5495,
8N-5495,
DONALDSON
P119176,
P150922,
FLEETGUARD
AF875M,
FRAM
CA598,
GENERAL MOTORS
6488362,
MAHLE FILTER
LX 1100,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Donsson Heavy Duty Air Filter DA2124 with Enhanced Spiralforce System & Bi-Density Polyurethane | Replacement for: 1B7716 1P6450 1P7716 2P1482 7W5495 & more
DONSSON Donsson Heavy Duty Air Filter DA2124 with Enhanced Spiralforce System & Bi-Density Polyurethane | Replacement for: 1B7716 1P6450 1P7716 2P1482 42980 6N2731 7W5495 8N5495 AF2306 AF875 AF875M AP1P7716 AP7716 AR598 AZ598 C30883 C30883/1 CA598 DX716 HCA598 LAF7716 P119167 P138818 P181118 PA2358 SFA598 SFA598P TF598 || ISO-CERTIFIED QUALITY: Manufactured and tested under ISO 9001 2015 and ISO 5011 standards, delivering reliable quality and a commitment to environmental responsibility. || INDUSTRY-LEADING EXPERIENCE: With over 30 years of expertise and millions of filters produced and sold, Donsson delivers trusted replacement filters for top diesel vehicle and machinery brands, ensuring precise fit and performance that meets or exceeds manufacturer specifications. || SPIRAFORCE TECHNOLOGY FOR SUPERIOR STRENGTH & FILTRATION Engineered with a spiral-wrapped, seamed tube reinforced by a central rib, our filters deliver maximum collapse resistance and structural consistency. Paired with high-efficiency filtering media, they effectively capture contaminants and maintain silica levels at 3-7 PPM—far below the manufacturer’s limit of 15 PPM—ensuring optimal engine protection and longevity. || SEAMLESS BONDING & AIRTIGHT GASKET FOR MAXIMUM FILTRATION Featuring seamless end cap-to-media bonding, our axxial filters ensure a flawless connection with no gaps for unfiltered air to bypass. The one-piece elastic gasket, made from soft, flexible material and chemically bonded to the end cap, provides an airtight seal that directs all airflow through the filtering media for superior engine protection.
DONSSON Donsson Heavy Duty Air Filter DA2124 with Enhanced Spiralforce System & Bi-Density Polyurethane | Replacement for: 1B7716 1P6450 1P7716 2P1482 42980 6N2731 7W5495 8N5495 AF2306 AF875 AF875M AP1P7716 AP7716 AR598 AZ598 C30883 C30883/1 CA598 DX716 HCA598 LAF7716 P119167 P138818 P181118 PA2358 SFA598 SFA598P TF598 || ISO-CERTIFIED QUALITY: Manufactured and tested under ISO 9001 2015 and ISO 5011 standards, delivering reliable quality and a commitment to environmental responsibility. || INDUSTRY-LEADING EXPERIENCE: With over 30 years of expertise and millions of filters produced and sold, Donsson delivers trusted replacement filters for top diesel vehicle and machinery brands, ensuring precise fit and performance that meets or exceeds manufacturer specifications. || SPIRAFORCE TECHNOLOGY FOR SUPERIOR STRENGTH & FILTRATION Engineered with a spiral-wrapped, seamed tube reinforced by a central rib, our filters deliver maximum collapse resistance and structural consistency. Paired with high-efficiency filtering media, they effectively capture contaminants and maintain silica levels at 3-7 PPM—far below the manufacturer’s limit of 15 PPM—ensuring optimal engine protection and longevity. || SEAMLESS BONDING & AIRTIGHT GASKET FOR MAXIMUM FILTRATION Featuring seamless end cap-to-media bonding, our axxial filters ensure a flawless connection with no gaps for unfiltered air to bypass. The one-piece elastic gasket, made from soft, flexible material and chemically bonded to the end cap, provides an airtight seal that directs all airflow through the filtering media for superior engine protection.
Veyronix P181118 P158670 Engine Air Filter KIT Compatible With CAT 3306 3306B G3306 Engine & 825C 826C Earthmoving Compactor Replaces Caterpillar 7W-5495, Fleetguard AF875M AF876, Wix 42980 42981
Veyronix Cross referencing OE: Compatible With Caterpillar 7W-5495 7W5495 1P7716 1P7360, Fleetguard AF875M AF876, Wix 42980 42981, Donaldson P181118 P158670 || Application Model:Compatible With CAT 3306 3306B G3306 Engine Industrial & 825C 826C Earthmoving Compactor || Application Model:Compatible With CAT 980C 980F 980F II Wheel-Type Loader / 824C Wheel Dozer / 963 973 Track-Type Loader / 621E 621S 623B 623E 627E Wheel Tractor-Scraper / D25D D300D D30D D350D D400D D40D Articulated Dump Truck / 57H 8 8A 8SU 8U D6D D6E D8N Track-Type Tractor || Manufactured to OEM standards and rigorously tested at the factory || Package Includes: 1 x Outer Air Filter P181118;1 x Inner Air Filte P158670
Veyronix Cross referencing OE: Compatible With Caterpillar 7W-5495 7W5495 1P7716 1P7360, Fleetguard AF875M AF876, Wix 42980 42981, Donaldson P181118 P158670 || Application Model:Compatible With CAT 3306 3306B G3306 Engine Industrial & 825C 826C Earthmoving Compactor || Application Model:Compatible With CAT 980C 980F 980F II Wheel-Type Loader / 824C Wheel Dozer / 963 973 Track-Type Loader / 621E 621S 623B 623E 627E Wheel Tractor-Scraper / D25D D300D D30D D350D D400D D40D Articulated Dump Truck / 57H 8 8A 8SU 8U D6D D6E D8N Track-Type Tractor || Manufactured to OEM standards and rigorously tested at the factory || Package Includes: 1 x Outer Air Filter P181118;1 x Inner Air Filte P158670
This part in 4 request:
Show.
This information for suppliers only!
2024-05-13
2023-04-11
2022-03-25
2021-09-06
Number on catalog scheme:
7
For full view, you need register
Compatible equipment models: 7W5495:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 125-0200 Camshaft Pilot As 2
C 125-0201 Camshaft Guide As 1
D 8T-3169 Crank Assembly 1
E 238-9586 Camshaft Drive Group 1
F 5P-3931 Anti-Seize Compound -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure is for installing the camshaft in the left-hand side of the engine.Note: The following Step is for 3512C, 3512E, and 3516C Engines.
Illustration 1 g01122346
Attach a suitable lifting device to rear half of the camshaft. The weight of one-half of the camshaft for 3516C Engine is approximately 47 kg (104 lb). The weight of one-half of the camshaft for 3512C and 3512E Engine is approximately 45 kg (99 lb). Install spacer (13) and the rear half of the camshaft onto the front half of the camshaft. Install bolts (14) and tighten to a torque of 55 7 N m (41 5 lb ft).Note: Ensure that the camshafts are assembled according to the marks on the ends of the camshafts. If the dowel was removed from the front half of the camshaft, install the dowel. Install the dowel to 12.0 0.5 mm (0.47 0.02 inch) from the surface of the camshaft.Note: The following Step is for 3508C Engines.
Attach a suitable lifting device to the camshaft. The weight of the camshaft for 3508C Engine is approximately 50 kg (110 lb).Note: Ensure that the camshaft is installed according to the marks on the ends of the camshaft. If the dowel was removed from the front half of the camshaft, install the dowel. Install the dowel to 12.0 0.5 mm (0.47 0.02 inch).
Illustration 2 g01123198
Install Tooling (C) on the front housing. Do not tighten the bolts on Tooling (C).Note: Tooling (C) can be installed on the flywheel housing in order to install the camshaft from the rear of the engine.
Install Tooling (B) on the ends of the camshaft. Install Tooling (D) on Tooling (B) which is installed on the front of the camshaft.
Ensure that the camshaft and the camshaft bearings are clean. Place clean engine oil on the lobes and the journals of the camshaft. Also place clean engine oil on the camshaft bearings.
Rotate the camshaft and insert the camshaft into the engine. Position the camshaft in the engine until Tooling (B) is in the front camshaft bearing. Rotate the camshaft in order to align Tooling (C) and the camshaft bores. Tighten the bolts for Tooling (C).
Rotate the camshaft and insert the camshaft into the engine. Remove Tooling (D) from Tooling (B). Remove Tooling (B) from the camshaft. Remove Tooling (C) from the front housing.
Illustration 3 g01122334
Install thrust washer (10) and bolts (11).
Install bolts (12).
If the camshaft is out of time more than 18 degrees (approximately 1/2 of the timing pin is out of the groove), the valves can make contact with the pistons. This will cause damage to the engine. Refer to Testing and Adjusting, "Camshaft Timing" for more information.
Illustration 4 g01122583
Remove
Table 1
Required Tools
Tool Part Number Part Description Qty
B 125-0200 Camshaft Pilot As 2
C 125-0201 Camshaft Guide As 1
D 8T-3169 Crank Assembly 1
E 238-9586 Camshaft Drive Group 1
F 5P-3931 Anti-Seize Compound -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure is for installing the camshaft in the left-hand side of the engine.Note: The following Step is for 3512C, 3512E, and 3516C Engines.
Illustration 1 g01122346
Attach a suitable lifting device to rear half of the camshaft. The weight of one-half of the camshaft for 3516C Engine is approximately 47 kg (104 lb). The weight of one-half of the camshaft for 3512C and 3512E Engine is approximately 45 kg (99 lb). Install spacer (13) and the rear half of the camshaft onto the front half of the camshaft. Install bolts (14) and tighten to a torque of 55 7 N m (41 5 lb ft).Note: Ensure that the camshafts are assembled according to the marks on the ends of the camshafts. If the dowel was removed from the front half of the camshaft, install the dowel. Install the dowel to 12.0 0.5 mm (0.47 0.02 inch) from the surface of the camshaft.Note: The following Step is for 3508C Engines.
Attach a suitable lifting device to the camshaft. The weight of the camshaft for 3508C Engine is approximately 50 kg (110 lb).Note: Ensure that the camshaft is installed according to the marks on the ends of the camshaft. If the dowel was removed from the front half of the camshaft, install the dowel. Install the dowel to 12.0 0.5 mm (0.47 0.02 inch).
Illustration 2 g01123198
Install Tooling (C) on the front housing. Do not tighten the bolts on Tooling (C).Note: Tooling (C) can be installed on the flywheel housing in order to install the camshaft from the rear of the engine.
Install Tooling (B) on the ends of the camshaft. Install Tooling (D) on Tooling (B) which is installed on the front of the camshaft.
Ensure that the camshaft and the camshaft bearings are clean. Place clean engine oil on the lobes and the journals of the camshaft. Also place clean engine oil on the camshaft bearings.
Rotate the camshaft and insert the camshaft into the engine. Position the camshaft in the engine until Tooling (B) is in the front camshaft bearing. Rotate the camshaft in order to align Tooling (C) and the camshaft bores. Tighten the bolts for Tooling (C).
Rotate the camshaft and insert the camshaft into the engine. Remove Tooling (D) from Tooling (B). Remove Tooling (B) from the camshaft. Remove Tooling (C) from the front housing.
Illustration 3 g01122334
Install thrust washer (10) and bolts (11).
Install bolts (12).
If the camshaft is out of time more than 18 degrees (approximately 1/2 of the timing pin is out of the groove), the valves can make contact with the pistons. This will cause damage to the engine. Refer to Testing and Adjusting, "Camshaft Timing" for more information.
Illustration 4 g01122583
Remove
Caterpillar parts catalog:
Parts filter Caterpillar catalog:
769D, 770, 770G, 771D, 772, 772G, 773D, 773E, 773F, 775D, 775E, 775F, 776D, 777D, 777F, 777G, 824C, 854G, 938H, 950H, 962H, 966H, 972H, 980C, D5R LGP, D6N, D6N LGP, D6N OEM, D8N, IT38H, IT62H, MH3037,...
814B, 815B, 816B, 824C, 826C, 950B, 950F, 955L, 966D, 966F, 977L, 980C, 980F, D4E, D5B, D6D
D7H, D8N
D7H, D8N
120G, 12G, 130G, 140G, 14G, 16G, 375, 375 L, 931B, 931C II
120G, 12G, 130G, 140G, 14G, 16G, 613C, 615, 615C, 621E, 627E, 631E, 633E II, 637E, 651E, 657E, 784B, 785, 785B, 789, 789B, 793B, 793C, 916, 926, 936, 936F, G936, IT28, IT28B
615, 621E, 621F, 627B, 627E
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H NA, 613G, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, ...
611, 615C, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, 834B, 988B, 992D
611, 613C II, 615C, 621F, 621G, 623E, 623F, 623G, 627F, 627G, 631G, 637G
611, 613C II, 615C, 621F, 621G, 623E, 623F, 623G, 627F, 627G, 631G, 637G, 69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777D, D250E, D250E II, D300E, D300E II
621F, 623E, 627F, 824G, 825G, 826G, 980C, 980F, 980G, D8N, D8R, D8R II
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 215C, 235, 235B, 235C, 235D, 330, 330 L, 3304, 3304B, 3306, 3...
16G, 16H NA, 245B, 3116, 3126, 3126B, 3126E, 3176B, 3176C, 3196, 3208, 3304, 3306, 3306B, 3306C, 3406B, 3406C, 3406E, 3412, 3412C, 3456, 375, 589, 621F, 623E, 627F, 631E, 633E II, 637D, 637E, 651E, 65...
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H NA, 1673C, 235B, ...
3126, 3208, 3304, 3306, 3306B, 3306C, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 3456, 3508C, 3512C, 3516B, 375, 375 L, 5080, AD55B, C-15, C-16, C-18, C15, C18, C27, C32, CX31-C15I, ...
12H, 140H, 143H, 14H, 160H, 163H, 16H, 3176, 3176B, 3176C, 3196, 3304, 3306, 3306B, 3306C, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 345B, 345B II, 345B II...
6E4698
FILTER GP-OIL
428B
428B
3304, 3304B, 3306, 3306B, D320A, D330A, D330B, G3304, G3306
3306, 3306B, C9, D330A, D333A, D333B, G3304, G3306, G343
120H, 12H, 12H ES, 12H NA, 135H, 140G, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 3126B, 3306, 3306B, 385C, 525B, 535B, 539, 545, 572R, 572R II...
120H, 12H, 12H ES, 12H NA, 135H, 140G, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 3126B, 3306, 3306B, 385C, 525B, 535B, 539, 545, 572R, 572R II...
1673, 3306, D342C, D8H
16G, 245, 3306, 3306B, 578, 583K, 621B, 621E, 621R, 623B, 623E, 627B, 627E, 75, 777, 824C, 826C, 963, 973, 980B, 980C, 980F, 992, D10, D250B, D25C, D25D, D300B, D300D, D30C, D350C, D35C, D35HP, D400, ...