8I4232 FILTER AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA8I4232
8I-4232
8I4232
CA8I4232
8I-4232
8I4232
Weight: 1 pounds 0 kg.
Cross Reference:
CATERPILLAR
3I2059,
8I4232,
CLARK
244530,
DONALDSON
P550699,
ALFAROME/FIAT/LANCI
710049229,
LUBERFINER
LH5739,
NEW HOLLAND
71004922,
TEREX
00420030,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
NUEPWRFA P550699 3I2059 8I4232 D3NN7C045A S300744 D52932 D0950547 5537711600 HYDRAULIC FILTER Compatible for CASE/CASE IH 621 CUMMINS 6BT5.9 CATERPILLAR PS 500 ATLAS COPCO ST 1530 SCOOPTRAM
NUEPWRFA Part number: P550699 3I2059 8I4232 D3NN7C045A S300744 D52932 D0950547 5537711600 || Compatible for CASE/CASE IH 621 CUMMINS 6BT5.9 CATERPILLAR PS 500 ATLAS COPCO ST 1530 SCOOPTRAM || Compatible for CEMET AGRIP 4500 S || Compatible for CLARK-HURTH DIVERS || Compatible for EPIROC Boomer L2 D SCOOPTRAM ST 14 || Compatible for FANTUZZI FDG 280 || Compatible for KALMAR 16-200 || Compatible for KOMATSU FOREST 828 836 838 862 862 902 902 H || Approx. Diamensionas: Outer Diameter 88 mm (3.46 inch) Inner Diameter 29 mm (1.14 inch) Length 140 mm (5.51 inch) || New aftermarket parts, the picture is just for reference. Manufactured to OEM standards and rigorously tested at the factory.
NUEPWRFA Part number: P550699 3I2059 8I4232 D3NN7C045A S300744 D52932 D0950547 5537711600 || Compatible for CASE/CASE IH 621 CUMMINS 6BT5.9 CATERPILLAR PS 500 ATLAS COPCO ST 1530 SCOOPTRAM || Compatible for CEMET AGRIP 4500 S || Compatible for CLARK-HURTH DIVERS || Compatible for EPIROC Boomer L2 D SCOOPTRAM ST 14 || Compatible for FANTUZZI FDG 280 || Compatible for KALMAR 16-200 || Compatible for KOMATSU FOREST 828 836 838 862 862 902 902 H || Approx. Diamensionas: Outer Diameter 88 mm (3.46 inch) Inner Diameter 29 mm (1.14 inch) Length 140 mm (5.51 inch) || New aftermarket parts, the picture is just for reference. Manufactured to OEM standards and rigorously tested at the factory.
For full view, you need register
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02475493
Illustration 2 g03701812
Ensure that engine cooler (3) is clean and free from damage. Ensure that the engine oil cooler is free from restriction.
Clean the gasket surfaces of the cylinder block.
Position a new gasket (4) onto engine oil cooler (3).
Push bolts (1) through the holes in the gasket. Note: The holes in the gasket have serrations that hold the bolts captive.
Position engine oil cooler (3) onto the cylinder block. Hand tighten bolts (2). Support the engine oil cooler as the bolts are installed.
Illustration 3 g03741794
Snug torque tightening sequence for the engine oil cooler
Tighten the bolts to a snug torque of 7.5 N m (66) in the sequence that is shown in Illustration 3.
Illustration 4 g03736218
Tightening sequence for the engine oil cooler
Tighten the bolts to a torque of 26 N m (230 lb in) in the sequence that is shown in Illustration 4.
Install spacer (1) (not shown). Tighten the bolts to a torque of 44 N m (32 lb ft). Refer to Illustration 2 End By:
Install the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Install" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02475493
Illustration 2 g03701812
Ensure that engine cooler (3) is clean and free from damage. Ensure that the engine oil cooler is free from restriction.
Clean the gasket surfaces of the cylinder block.
Position a new gasket (4) onto engine oil cooler (3).
Push bolts (1) through the holes in the gasket. Note: The holes in the gasket have serrations that hold the bolts captive.
Position engine oil cooler (3) onto the cylinder block. Hand tighten bolts (2). Support the engine oil cooler as the bolts are installed.
Illustration 3 g03741794
Snug torque tightening sequence for the engine oil cooler
Tighten the bolts to a snug torque of 7.5 N m (66) in the sequence that is shown in Illustration 3.
Illustration 4 g03736218
Tightening sequence for the engine oil cooler
Tighten the bolts to a torque of 26 N m (230 lb in) in the sequence that is shown in Illustration 4.
Install spacer (1) (not shown). Tighten the bolts to a torque of 44 N m (32 lb ft). Refer to Illustration 2 End By:
Install the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Install" for the correct procedure.
Parts filter Caterpillar catalog:
8H9755
FILTER A.
Caterpillar
Caterpillar
8H8650
FILTER G.
Caterpillar
Caterpillar
8H7099
FILTER G.-OIL
Caterpillar
Caterpillar
8H1940
FILTER A.
Caterpillar
Caterpillar
8F7470
FILTER G.-OIL
Caterpillar
Caterpillar
8F7354
FILTER A.
Caterpillar
Caterpillar
8N4622
FILTER-ORIFICE
Caterpillar
Caterpillar
8N4621
FILTER-
Caterpillar
Caterpillar
8N2673
FILTER G
Caterpillar
Caterpillar
8N0202
FILTER-PAD
Caterpillar
Caterpillar
8J9354
FILTER G OIL
Caterpillar
Caterpillar
8J1595
FILTER G OIL
Caterpillar
Caterpillar