8X0363 FILTER & LINES GP-TORQUE CONV Caterpillar parts
776C, 776D, 777D
Rating:
Alternative (cross code) number:
CA8X0363
8X-0363
8X0363
CA8X0363
8X-0363
8X0363
Weight: 14 pounds 6 kg.
TRACTOR, TRUCK,
Information:
START BY:a. remove pistons and connecting rods1. Drain the coolant from the cylinder block.2. Put covers on the crankshaft journals for protection from dirt and water. 3. Remove the cylinder liners with tooling (A). 4. Remove seals (1) and filler band (2) from each liner.Install Cylinder Liners
1. Clean the cylinder liners and liner bores in the block.2. Install the liners in the block without seals or bands. 3. Check the cylinder liner (projection) height as follows:a. Install four bolts and washers (3) from tooling (A) around each cylinder liner as shown. Tighten the bolts evenly to a torque of 95 N m (70 lb.ft.).b. Install bar (4), plate (5), plates (2), bolts (1) and washers from tooling (A). Be sure the bar is in position at the center of the liner and the liner surface is clean. Tighten bolts (1) evenly to a torque of 70 N m (50 lb.ft.).c. Check the distance from the bottom edge of bar (4) to the top edge of the spacer plate. The distance on each end of the bar must be the same.d. Check the liner (projection) height with tool (B) at four locations around the liner. Liner (projection) height must be 0.025 to 0.152 mm (.001 to .006 in.). The difference between the four measurements on the same liner must not be more than 0.05 mm (.002 in.). The difference between liner (projection) height for liners next to each other must not be more than 0.05 mm (.002 in.). The maximum permissible difference between the average height (projection) of all the cylinder liners under one cylinder head is 0.08 mm (.003 in.). If the liner is turned in the cylinder block, it can make a difference in liner (projection) height. 4. If the liner (projection) height is not 0.13 0.08 mm (.005 .003 in.), check the thickness of the following parts:a. Spacer plate (X): 8.59 0.03 mm (.338 .001 in.).b. Spacer gasket (Y): 0.20 0.03 mm (.008 .001 in.). All surfaces must be clean and dry when the gasket is installed.c. Cylinder liner flange (Z): 8.890 0.020 mm (.350 .0008 in.). The cylinder liner (projection) height can be changed by the adjustment of a counterbore in the block. A 5N93 Stainless Steel Insert is also available for use after the cylinder block has been counterbored. Special Instruction, Form No. SMHS8222 has the correct installation procedure for the insert.5. Put a mark on the cylinder liners and block so the liners can be installed in the same position.6. Remove tooling (A) and tool (B). Remove one liner.7. Put liquid soap on seals (6), grooves of the liner and the bore of the block.8. Put filler band (5) in clean engine oil for a short moment. Install the filler band on the liner.9. Install the liner immediately after the filler band is installed. Make sure the mark on the liner is in alignment with the mark on the block. Use tooling (C) to push
1. Clean the cylinder liners and liner bores in the block.2. Install the liners in the block without seals or bands. 3. Check the cylinder liner (projection) height as follows:a. Install four bolts and washers (3) from tooling (A) around each cylinder liner as shown. Tighten the bolts evenly to a torque of 95 N m (70 lb.ft.).b. Install bar (4), plate (5), plates (2), bolts (1) and washers from tooling (A). Be sure the bar is in position at the center of the liner and the liner surface is clean. Tighten bolts (1) evenly to a torque of 70 N m (50 lb.ft.).c. Check the distance from the bottom edge of bar (4) to the top edge of the spacer plate. The distance on each end of the bar must be the same.d. Check the liner (projection) height with tool (B) at four locations around the liner. Liner (projection) height must be 0.025 to 0.152 mm (.001 to .006 in.). The difference between the four measurements on the same liner must not be more than 0.05 mm (.002 in.). The difference between liner (projection) height for liners next to each other must not be more than 0.05 mm (.002 in.). The maximum permissible difference between the average height (projection) of all the cylinder liners under one cylinder head is 0.08 mm (.003 in.). If the liner is turned in the cylinder block, it can make a difference in liner (projection) height. 4. If the liner (projection) height is not 0.13 0.08 mm (.005 .003 in.), check the thickness of the following parts:a. Spacer plate (X): 8.59 0.03 mm (.338 .001 in.).b. Spacer gasket (Y): 0.20 0.03 mm (.008 .001 in.). All surfaces must be clean and dry when the gasket is installed.c. Cylinder liner flange (Z): 8.890 0.020 mm (.350 .0008 in.). The cylinder liner (projection) height can be changed by the adjustment of a counterbore in the block. A 5N93 Stainless Steel Insert is also available for use after the cylinder block has been counterbored. Special Instruction, Form No. SMHS8222 has the correct installation procedure for the insert.5. Put a mark on the cylinder liners and block so the liners can be installed in the same position.6. Remove tooling (A) and tool (B). Remove one liner.7. Put liquid soap on seals (6), grooves of the liner and the bore of the block.8. Put filler band (5) in clean engine oil for a short moment. Install the filler band on the liner.9. Install the liner immediately after the filler band is installed. Make sure the mark on the liner is in alignment with the mark on the block. Use tooling (C) to push
Caterpillar SIS machinery equipment:
Caterpillar SIS
777C Truck 776C Tractor 2TK00001-UP (MACHINE) POWERED BY 3508 Engine »
8X-0363
FILTER & LINES GP-TORQUE CONV
777C Truck 776C Tractor 2TK00001-UP (MACHINE) POWERED BY 3508 Engine »
8X-0363
FILTER & LINES GP-TORQUE CONV
777C Truck 776C Tractor 2TK00001-UP (MACHINE) POWERED BY 3508 Engine »
8X-0363
FILTER & LINES GP-TORQUE CONV
776D Tractor 5ER00001-UP (MACHINE) POWERED BY 3508B Engine »
8X-0363
FILTER & LINES GP-TORQUE CONV
777D Truck 3PR00001-UP (MACHINE) POWERED BY 3508 Engine »
8X-0363
FILTER & LINES GP-TORQUE CONV
777D HAA Off-Highway Truck 2YW00001-UP (MACHINE) POWERED BY 3512B Engine »
8X-0363
FILTER & LINES GP-TORQUE CONV
776D Tractor AFS00001-UP (MACHINE) POWERED BY 3508B Engine »
8X-0363
FILTER & LINES GP-TORQUE CONV
777D Off-Highway Truck AGC00001-UP (MACHINE) POWERED BY 3508B Engine »
8X-0363
FILTER & LINES GP-TORQUE CONV
777D Truck AGY00001-UP (MACHINE) POWERED BY 3512B Engine »
8X-0363
FILTER & LINES GP-TORQUE CONV
Caterpillar parts catalog:
Parts filter Caterpillar catalog:
2752604
FILTER-ENGINE OIL
16H, 24H, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 797, 797B, 834G, 85...
16H, 24H, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 797, 797B, 834G, 85...
1110716
FILTER ELEMENT-FUEL
3512B, 3516B, 3516C, 777D, 784C, 785B, 785C, 789C, 793C, C15, C175-16, C27, C32, PM3516, SCT673, SPT342, XQC1200, XQC1600
3512B, 3516B, 3516C, 777D, 784C, 785B, 785C, 789C, 793C, C15, C175-16, C27, C32, PM3516, SCT673, SPT342, XQC1200, XQC1600
1N4864
FILTER ELEMENT AS-AIR
375, 375 L, 5080, 69D, 776D, 777D, 784B, 784C, 785, 785B, 785C, AD40, AD45, AD45B, AD55, AE40, AE40 II, G3412, PM-201
375, 375 L, 5080, 69D, 776D, 777D, 784B, 784C, 785, 785B, 785C, AD40, AD45, AD45B, AD55, AE40, AE40 II, G3412, PM-201
1R0719
FILTER ELEMENT AS-OIL
120G, 120H, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16H, 16H NA, 517, 527, 528B, 530B, 561M, 589, 611, 613C, 613C II, 61...
120G, 120H, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16H, 16H NA, 517, 527, 528B, 530B, 561M, 589, 611, 613C, 613C II, 61...
1328875
FILTER ELEMENT AS-OIL
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 517, 527, 561M, 589...
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 517, 527, 561M, 589...
1328876
FILTER ELEMENT AS-OIL
24H, 561M, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 613C II, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 769C, 769D, 771C, 771D, 773B, 773D, 775B, 775D, 776C, 776D, 777, 777D, 777F, 777G, 784B, 784...
24H, 561M, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 613C II, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 769C, 769D, 771C, 771D, 773B, 773D, 775B, 775D, 776C, 776D, 777, 777D, 777F, 777G, 784B, 784...
4T3132
FILTER ELEMENT AS-OIL
24H, 572R II, 578, 583R, 583T, 587R, 587T, 613C II, 769C, 769D, 771C, 771D, 773B, 773D, 775B, 775D, 776C, 776D, 777, 777D, 777F, 784B, 784C, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 930R, ...
24H, 572R II, 578, 583R, 583T, 587R, 587T, 613C II, 769C, 769D, 771C, 771D, 773B, 773D, 775B, 775D, 776C, 776D, 777, 777D, 777F, 784B, 784C, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 930R, ...
8C9657
FILTER ELEMENT AS-CAB AIR
611, 613C II, 615C, 621F, 621G, 623E, 623F, 623G, 627F, 627G, 631G, 637G, 69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777D, D250E, D250E II, D300E, D300E II
611, 613C II, 615C, 621F, 621G, 623E, 623F, 623G, 627F, 627G, 631G, 637G, 69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777D, D250E, D250E II, D300E, D300E II
1R0778
FILTER ELEMENT AS-OIL
776D, 777D, 777F, 777G, 784C, 785C, 785D, 789C, 793C, 793D, 797, 797B, D7G, D7G2, D8R II, D8T
776D, 777D, 777F, 777G, 784C, 785C, 785D, 789C, 793C, 793D, 797, 797B, D7G, D7G2, D8R II, D8T
2852486
FILTER & LINES GP-HYDRAULIC
321D LCR
321D LCR
2116053
FILTER GP-OIL
583T, D8T
583T, D8T
9T8157
FILTER GP-HYDRAULIC
302.5, D6H, D6H XL, D6H XR
302.5, D6H, D6H XL, D6H XR
3436068
FILTER & MTG GP-HYDRAULIC
CB-44B, CB-54B
CB-44B, CB-54B
2230560
FILTER & LINES GP-FUEL
D6R III
D6R III
3687694
FILTER & MTG GP-ENGINE OIL
320D GC, 320D L, 323D L
320D GC, 320D L, 323D L
2078358
FILTER & MTG GP-POWER TRAIN
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
3481088
FILTER GP-OIL
844K, 854K, 990K, 992K, 993K, D10T2, D11T
844K, 854K, 990K, 992K, 993K, D10T2, D11T