FINAL DRIVE GP 6A7259 - Caterpillar

Illustration 27 g03741023
(11) 8T-4121 Hard Washer
(30) 8C-3206 Half Flange
(31) 8T-4196 Bolts
(32) 4J-0520 O-Ring Seal
(35) 8X-5027 Elbow
(40) 391-6993 Hose and Tube As
Attach 391-6993 Hose and Tube As (40) to 8X-5027 Elbow (35) with one 4J-0520 O-Ring Seal (32), two 8C-3206 Half Flanges (30), four 8T-4196 Bolts (31), and four 8T-4121 Hard Washers (11). Tighten the bolts to 55 10 N m (41 7 lb ft).
Illustration 28 g03741056
(G) 324-0780 Steering Valve Gp
(36) 8T-5005 Bolts
(40) 391-6993 Hose and Tube As
(41) 235-2474 Rectangular Seal
(42) 198-4777 Hard Washer
Route 391-6993 Hose and Tube As (40) down towards 324-0780 Steering Valve Gp (G).
Attach 391-6993 Hose and Tube As (40) to 324-0780 Steering Valve Gp (G) using one 235-2474 Rectangular Seal (41), four 8T-5005 Bolts (36), and four 198-4777 Hard Washers (42). Tighten the bolts to 55 10 N m (41 7 lb ft).
Illustration 29 g03741068
(F) 455-1846 Piston Pump Gp
(H) 452-7173 Hose As
(J) 373-1565 Accumulator Charging Valve
(43) 155-3624 Plug As
Remove 452-7173 Hose As (H) from between 455-1846 Piston Pump Gp (F) and 373-1565 Accumulator Charging Valve (J) and discard. Install 155-3624 Plug As (43) where 452-7173 Hose As (H) was removed from 455-1846 Piston Pump Gp (F).
Illustration 30 g03741202
(40) 391-6993 Hose and Tube As
(44) 148-0913 Hose As
(45) 148-8353 Elbow As
Install 148-0913 Hose As (44) onto 391-6993 Hose and Tube As (40) with one 148-8353 Elbow As (45).
Illustration 31 g03741380
(H) 452-7173 Hose As
(J) 373-1565 Accumulator Charging Valve
(44) 148-0913 Hose As
(46) 6E-4701 Check Valve Gp
Connect free end of 148-0913 Hose As (44) where 452-7173 Hose As (H) was removed from 373-1565 Accumulator Charging Valve (J) with one 6E-4701 Check Valve Gp (46) along with existing hardware. Refer to Illustration 31.
Illustration 32 g03741407
View of the complete secondary system.
Software Configuration
Note: This machine feature can be configured and must be activated with product software programming system or service tool.
Use Caterpillar Electronic Technician (CAT ET) and select the Implement Electronic Control Module (ECM).
Select "Configuration" from the menu.
Double click on the desired feature on the "Configuration" screen.
Select the desired status of the feature and click "OK". The feature will be activated on the next power cycle. Note: A self-test will be performed after every key on power cycle