1782612 FITTING GP-FUEL LINES Caterpillar parts
3126B, 3126E, C-9, C7, C9
Rating:
Alternative (cross code) number:
CA1782612
178-2612
1782612
CA1782612
178-2612
1782612
TRUCK ENGINE,
Number on catalog scheme:
For full view, you need register
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The aftercooler has been removed for photographic purposes only.
Illustration 1 g00754079
Replace O-ring (24). Lubricate the O-ring with light oil at installation.
Illustration 2 g00753972
Attach the appropriate nylon sling and a suitable lifting device to the Unit injector hydraulic pump. The approximate weight of the pump is 30 kg (65 lb).
Position the unit injector hydraulic pump in place. Carefully, slide the pump into position. Install two bolts (23) and washers.
Remove the nylon strap from the unit injector hydraulic pump.
Illustration 3 g00753967
Install three bolts (22). One bolt is on the other side of the unit injector hydraulic pump.
Illustration 4 g00753966
Connect the oil temperature sensor at connector (21). Connect the oil pressure sensor at connector (20). Connect the rail pressure control valve (19) .
Illustration 5 g00753932
Install wire ties at positions (19) .
Illustration 6 g00753929
Install three tube assemblies (18) to the unit injector hydraulic pump. Attach hose assembly (17) to the pump.Note: Make sure that the tube assembly for the left bank is installed to the lower port.
Illustration 7 g00753821
Position bracket (14) in place and install two bolts (15). Attach ground wire (16) to bracket (14) .
Illustration 8 g00753823
Tighten the two nuts (13) that are holding the ground wires to bracket (14) .
Position the connector (11) in place on connector (10). Insert screw (12) that holds the connectors together.
Illustration 9 g00753804
Install new O-ring (9) onto tube assembly (8). Insert tube assembly into the engine and hook up the other end of the tube assembly (6) to the pump. Place clip (7) in position and install the bolt.
Illustration 10 g00753793
Position hose assembly (5) with the two clamps (3) and install bolt (2) .
Install hose assembly (1) to the unit injector hydraulic pump.
Check the engine oil for the proper level.
Prime the fuel system.Reference: For information about priming the fuel system, refer to the Operation and Maintenance Manual, "Maintenance Section".
Install the muffler assembly.Reference: Refer to the Disassembly and assembly, "Remove and Install Muffler Assembly".
Install the hood group.Reference: Refer to the Disassembly and Assembly, "Remove and Install Hood Group".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The aftercooler has been removed for photographic purposes only.
Illustration 1 g00754079
Replace O-ring (24). Lubricate the O-ring with light oil at installation.
Illustration 2 g00753972
Attach the appropriate nylon sling and a suitable lifting device to the Unit injector hydraulic pump. The approximate weight of the pump is 30 kg (65 lb).
Position the unit injector hydraulic pump in place. Carefully, slide the pump into position. Install two bolts (23) and washers.
Remove the nylon strap from the unit injector hydraulic pump.
Illustration 3 g00753967
Install three bolts (22). One bolt is on the other side of the unit injector hydraulic pump.
Illustration 4 g00753966
Connect the oil temperature sensor at connector (21). Connect the oil pressure sensor at connector (20). Connect the rail pressure control valve (19) .
Illustration 5 g00753932
Install wire ties at positions (19) .
Illustration 6 g00753929
Install three tube assemblies (18) to the unit injector hydraulic pump. Attach hose assembly (17) to the pump.Note: Make sure that the tube assembly for the left bank is installed to the lower port.
Illustration 7 g00753821
Position bracket (14) in place and install two bolts (15). Attach ground wire (16) to bracket (14) .
Illustration 8 g00753823
Tighten the two nuts (13) that are holding the ground wires to bracket (14) .
Position the connector (11) in place on connector (10). Insert screw (12) that holds the connectors together.
Illustration 9 g00753804
Install new O-ring (9) onto tube assembly (8). Insert tube assembly into the engine and hook up the other end of the tube assembly (6) to the pump. Place clip (7) in position and install the bolt.
Illustration 10 g00753793
Position hose assembly (5) with the two clamps (3) and install bolt (2) .
Install hose assembly (1) to the unit injector hydraulic pump.
Check the engine oil for the proper level.
Prime the fuel system.Reference: For information about priming the fuel system, refer to the Operation and Maintenance Manual, "Maintenance Section".
Install the muffler assembly.Reference: Refer to the Disassembly and assembly, "Remove and Install Muffler Assembly".
Install the hood group.Reference: Refer to the Disassembly and Assembly, "Remove and Install Hood Group".
Caterpillar SIS machinery equipment:
Caterpillar SIS
3126B Truck Engine 8YL00001-UP »
178-2612
FITTING GP-FUEL LINES
C9 Truck Engine 9DG00001-UP »
178-2612
FITTING GP-FUEL LINES
3126B And 3126E Truck Engines BKD00001-UP »
178-2612
FITTING GP-FUEL LINES
3126E Truck Engine CKM00001-UP »
178-2612
FITTING GP-FUEL LINES
3126E Truck Engine 9SZ00001-UP »
178-2612
FITTING GP-FUEL LINES
3126E Truck Engine CRP00001-UP »
178-2612
FITTING GP-FUEL LINES
3126E Truck Engine HEP00001-UP »
178-2612
FITTING GP-FUEL LINES
C9 Military Vehicle Engine CKP00001-UP »
178-2612
FITTING GP-FUEL LINES
C9 Urban Transit Bus Engine MTB00001-UP »
178-2612
FITTING GP-FUEL LINES
C7 On-highway Engine KAL00001-UP »
178-2612
FITTING GP-FUEL LINES
C9 On-highway Engine ETK00001-UP »
178-2612
FITTING GP-FUEL LINES
C7 On-highway Engine LBM00001-UP »
178-2612
FITTING GP-FUEL LINES
Cat SIS web machinery list:
Parts fitting Caterpillar catalog:
120H, 120H ES, 120H NA, 135H, 135H NA, 205B, 206B, 211B, 213B, 214B, 3114, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 35, 446B, 446D, 45, 525B, 533, 535B, 539, ...
1674, 1693, 215, 215B, 215C, 215D, 216, 216B, 216B3, 219D, 225, 225D, 226B, 226B3, 228, 229, 229D, 231D, 232B, 235, 235B, 235C, 235D, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 245, 245B, 245D, 246C, ...
215B, 215D, 216, 216B, 216B3, 219D, 225, 225D, 226B, 226B3, 228, 229, 229D, 231D, 232B, 235B, 235C, 235D, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 245B, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B...
1090, 115, 1190, 1190T, 120H, 120M, 120M 2, 1290T, 12H, 12M, 12M 2, 12M 3 AWD, 135H, 1390, 140H, 140M, 140M 2, 140M 3 AWD, 143H, 14M, 160H, 160M, 160M 2, 160M 3 AWD, 163H, 16M, 214B, 24M, 2590, 301.6C...
1673C, 3116, 3126, 3126B, 3306, 3408, 637D, 920, 930, 983, G3306
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, 163H ...
3535102
FITTING AS-ELBOW
24M, 3126, 3126B, 3126E, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 365C, 365C L, 36...
24M, 3126, 3126B, 3126E, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 365C, 365C L, 36...
1487457
FITTING
3116, 3126, 3126B
3116, 3126, 3126B
1487459
FITTING
3116, 3126, 3126B
3116, 3126, 3126B
1555589
FITTING
3116, 3126, 3126B
3116, 3126, 3126B
1125286
FITTING GP-EXHAUST
3406B, 3406C
3406B, 3406C
2Y7974
FITTING GP-EXHAUST
3304, 3304B
3304, 3304B
1708403
FITTING GP-EXHAUST
3412C, C32
3412C, C32
3922932
FITTING GP-HYDRAULIC
M313D, M315D, M316D, M318D, M318D MH, M322D, M322D MH
M313D, M315D, M316D, M318D, M318D MH, M322D, M322D MH
2622129
FITTING GP-RADIATOR VENT
AD30, AD45, AD45B, AD55, AD55B, AD60
AD30, AD45, AD45B, AD55, AD55B, AD60
1957414
FITTING GP-AIR COMPRESSOR
3126B, 3126E, C7
3126B, 3126E, C7
2911097
FITTING GP-AIR SHUTOFF
C175-16
C175-16