AVSPARE.COM
parts catalog

FLAPPER-LOWER 6L7135 - Caterpillar



6L7135 FLAPPER-LOWER Caterpillar parts G3408, G3412, G342C, G353D, G379 FLAPPER
Rating:
34
Alternative (cross code) number:
CA6L7135
6L-7135
6L7135
Caterpillar 6L7135 FLAPPER-LOWER
Weight: 0.01 pounds 0 kg.

Buy FLAPPER-LOWER 6L7135 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE,

Compatible equipment models: 6L7135:

GAS ENGINE  G3408   G3412   G342C   G353D   G379   Caterpillar
Number on catalog scheme: 45
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8221 Lifting Sling 2 Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the correct procedure.
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" for the correct procedure.
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the correct procedure.
If necessary, remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove" for the correct procedure.
If necessary, remove the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The engine should be mounted on a suitable stand and placed in the inverted position.
If the cylinder head, the pistons and the connecting rods have not been removed already, remove the connecting rod bearings. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Remove" for the correct procedure.
Ensure that the main bearing caps are marked for the location and orientation.
Illustration 1 g02204377
Remove bolts (3) from tube assembly (2).
Remove tube assembly (2) from the cylinder block.
Remove gaskets (1) (not shown).
Illustration 2 g02212653
Illustration 3 g02212654
Remove bolts (4) and main bearing caps (5) from the cylinder block.
Remove lower main bearing shells (6) from main bearing caps (5). Keep the lower main bearing shells with the respective main bearing caps. Note: The lower main bearing shells are plain bearings that have no oil holes.
Illustration 4 g02212693
For number six main bearing, remove two thrust washers (7) from the cylinder block. In order to remove thrust washers (7), rotate the crankshaft in the correct direction. If necessary, push the crankshaft toward the front of the engine while you rotate the crankshaft, in order to aid removal. If necessary, push the crankshaft toward the rear of the engine while you rotate the crankshaft, in order to aid removal. Note: The thrust washers have a locating tab at one end.
Illustration 5 g02212655
Attach Tooling (A) and a suitable lifting device to crankshaft (8). Lift crankshaft (8) out of the cylinder block. The weight of the crankshaft is approximately 61 kg (134 lb). Note: Do not damage any of the finished surfaces on the crankshaft. When the crankshaft is removed from the engine, the crankshaft must be supported on a suitable stand in order to prevent damage to the crankshaft timing ring.
Illustration 6 g02212656
Remove upper main bearing shells (9) from the cylinder block. Keep the upper main bearing shells with the respective main bearing caps. Note: The upper main bearing shells have a groove and two oil holes.
If necessary, remove the crankshaft timing ring. Refer to Disassembly and Assembly, "Crankshaft Timing Ring - Remove and Install" for the correct procedure.
If necessary, remove the crankshaft gear. Refer to Disassembly and Assembly, "Crankshaft Gear - Remove and Install" for the correct procedure.

Caterpillar parts catalog:

Caterpillar parts catalog
G3408 Engine 6NB00001-UP
G3412 Engine 7DB00001-UP


Parts flapper Caterpillar catalog:

6L7136 FLAPPER-UPPER
G3408, G3412, G342C, G353D, G379
6L7136 FLAPPER-UPPER
G3408, G3412, G342C, G353D, G379
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.