6K9624 FLOOR MAT Caterpillar parts
992
Rating:
Alternative (cross code) number:
CA6K9624
6K-9624
6K9624
CA6K9624
6K-9624
6K9624
Weight: 0.01 pounds 0 kg.
WHEEL LOADER,
Compatible equipment models: 6K9624:
Number on catalog scheme:
For full view, you need register
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Information:
Head Seal Locations
Illustration 3 g01640536
Threaded gland with standard head seal
The head seal for the oversize threaded gland cylinder is the standard O-ring and back-up ring (1).
Illustration 4 g01640543
Threaded crown with oval seal
The head seal for the oversize threaded-crown cylinder is an oval cross-section seal (2). The seal is located in the lead-in chamfer at the open end of the cylinder. The O-ring and back-up ring groove (A) in the head is left empty
Illustration 5 g01640566
Bolted-Head Cylinder
Formerly, the head seal for the oversize bolted-head cylinder was the same oval seal (6) that is used in an oversize threaded-crown cylinder. The oversize bolted-head cylinder is now sealed at the head joint (3) by an O-ring (4). This O-ring (4) provides a more effective seal than the oval head seal. The groove (5) for the stock seal is left empty.Seal Installation Information
Rod Seal Installation
Illustration 6 g01644830
Install buffer seal (2) by hand. The sealing lip of the buffer seal should face the pressure side of the cylinder. The seal will take on a kidney shape during installation. Then, install the back-up ring (3). The backup ring should be installed closest to the rod eye end. Make sure that you do not twist the back-up ring.
Next, install the U-cup seal (6) next. Install the U-cup seal by hand. The "U" of the U-cupped seal should face toward the piston.
The head wear ring (1) is rigid and the wear ring is split to aid in assembly. Compress head wear ring (1) and slide the head wear ring down into position until the wear ring snaps into place.
Use the following procedure to install wiper seal (8).Note: The wiper seal (8) can be a press-in style that uses a metal shell or the wiper seal can be a snap-in style. The snap-in style does not require the use of bearing mount compound.
Scuff the surface of the counterbore in the head as well as the outside diameter of the wiper seal's (8) metal shell with emery cloth.
Clean the counterbore in the head and the outside diameter of the wiper seal metal shell with 6V-1541 Quick Cure Primer. Clean the counterbore and the metal shell until neither of the components discolor a clean white towel.Note: The metal shell of the wiper seal is coated with a corrosion inhibitor. This coating may prevent proper bonding of the wiper seal to the cylinder head if the inhibitor is not removed. After cleaning, do not touch the counterbore or the metal shell because the oil from your fingers may prevent a good bond. Handle the seal by the lip only.
Apply 6V-1541 Quick Cure Primer on the counterbore and the metal shell. Allow the primer to dry. The primer will dry in approximately 30 seconds.
Apply 7M-7456 Bearing Mount Compound evenly, but do not apply the Bearing Mount Compound excessively. Apply Bearing Mount Compound to the counterbore and to the metal shell. Do NOT allow the Bearing Mount Compound to contact the sealing lip.
Press wiper seal (8) into the cylinder head. Make sure that
Illustration 3 g01640536
Threaded gland with standard head seal
The head seal for the oversize threaded gland cylinder is the standard O-ring and back-up ring (1).
Illustration 4 g01640543
Threaded crown with oval seal
The head seal for the oversize threaded-crown cylinder is an oval cross-section seal (2). The seal is located in the lead-in chamfer at the open end of the cylinder. The O-ring and back-up ring groove (A) in the head is left empty
Illustration 5 g01640566
Bolted-Head Cylinder
Formerly, the head seal for the oversize bolted-head cylinder was the same oval seal (6) that is used in an oversize threaded-crown cylinder. The oversize bolted-head cylinder is now sealed at the head joint (3) by an O-ring (4). This O-ring (4) provides a more effective seal than the oval head seal. The groove (5) for the stock seal is left empty.Seal Installation Information
Rod Seal Installation
Illustration 6 g01644830
Install buffer seal (2) by hand. The sealing lip of the buffer seal should face the pressure side of the cylinder. The seal will take on a kidney shape during installation. Then, install the back-up ring (3). The backup ring should be installed closest to the rod eye end. Make sure that you do not twist the back-up ring.
Next, install the U-cup seal (6) next. Install the U-cup seal by hand. The "U" of the U-cupped seal should face toward the piston.
The head wear ring (1) is rigid and the wear ring is split to aid in assembly. Compress head wear ring (1) and slide the head wear ring down into position until the wear ring snaps into place.
Use the following procedure to install wiper seal (8).Note: The wiper seal (8) can be a press-in style that uses a metal shell or the wiper seal can be a snap-in style. The snap-in style does not require the use of bearing mount compound.
Scuff the surface of the counterbore in the head as well as the outside diameter of the wiper seal's (8) metal shell with emery cloth.
Clean the counterbore in the head and the outside diameter of the wiper seal metal shell with 6V-1541 Quick Cure Primer. Clean the counterbore and the metal shell until neither of the components discolor a clean white towel.Note: The metal shell of the wiper seal is coated with a corrosion inhibitor. This coating may prevent proper bonding of the wiper seal to the cylinder head if the inhibitor is not removed. After cleaning, do not touch the counterbore or the metal shell because the oil from your fingers may prevent a good bond. Handle the seal by the lip only.
Apply 6V-1541 Quick Cure Primer on the counterbore and the metal shell. Allow the primer to dry. The primer will dry in approximately 30 seconds.
Apply 7M-7456 Bearing Mount Compound evenly, but do not apply the Bearing Mount Compound excessively. Apply Bearing Mount Compound to the counterbore and to the metal shell. Do NOT allow the Bearing Mount Compound to contact the sealing lip.
Press wiper seal (8) into the cylinder head. Make sure that
Parts floor Caterpillar catalog:
2571110
FLOOR MAT
323D L, 323D LN, 324D, 324D L, 324D LN, 325D, 325D L, 329D L, 330D, 330D L, 330D LN, 330D MH, 336D L, 345C, 345C L, 345D, 345D L, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390...
323D L, 323D LN, 324D, 324D L, 324D LN, 325D, 325D L, 329D L, 330D, 330D L, 330D LN, 330D MH, 336D L, 345C, 345C L, 345D, 345D L, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390...
3436130
FLOOR MAT GP
CB-44B, CB-54B, CD-54B
CB-44B, CB-54B, CD-54B
7D3850
FLOOR AND SEAT MAT GROUP
12F, 14E
12F, 14E
3423536
FLOOR MAT
312D L, 315D L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 323D LN, 324D L, 329D, 329D L, 329D LN, 336D, 336D LN, 336D2, 345D L, 345D L VG, 349D L
312D L, 315D L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 323D LN, 324D L, 329D, 329D L, 329D LN, 336D, 336D LN, 336D2, 345D L, 345D L VG, 349D L
3311693
FLOOR MAT GP
AP1000E, AP1055E, BG1000E, BG1055E
AP1000E, AP1055E, BG1000E, BG1055E
2322964
FLOOR GP-SOUND SUPPRESSION
950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, IT62H
950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, IT62H
2844376
FLOOR MAT
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315D L, 318D2 L, 319D L
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315D L, 318D2 L, 319D L
2405071
FLOOR MAT
315D L, 318D L, 319D L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 323D L, 323D SA, 323D2 L, 324D, 324D L, 325D, 325D L, 325D MH, 326D L, 329D, 3...
315D L, 318D L, 319D L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 323D L, 323D SA, 323D2 L, 324D, 324D L, 325D, 325D L, 325D MH, 326D L, 329D, 3...
3406492
FLOOR MAT
312D L, 315D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 323D LN, 324D L, 329D, 336D, 345D L
312D L, 315D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 323D LN, 324D L, 329D, 336D, 345D L