4D2698 FORK Caterpillar parts
120B, 12E, 140B
Rating:
Alternative (cross code) number:
CA4D2698
4D-2698
4D2698
CA4D2698
4D-2698
4D2698
Weight: 3 pounds 1 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$80.38
07 Jun 2022
3.3069[1.49] Pounds
US: ProperBuy
Caterpillar FORK (4D2698)
CTP
CTP
$87.23
29 Apr 2020
-: -
4D2698 - FORK fits Caterpillar (CAT)
4D2698 Fork
4D2698 Fork
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 238-9586 Camshaft Drive Group 1
B 1P-0820 Hydraulic Puller 1
8B-7548 Push-Puller Tool Group 1
8B-7559 Adapter 2
5H-1504 Hard Washer 3
9U-6600 Hand Hydraulic Pump 1
C 125-0200 Camshaft Pilot As 2
D 125-0201 Camshaft Guide As 1
E 8T-3169 Crank Assembly 1 Start By:
Remove the valve cover base. Refer to Disassembly and Assembly, "Valve Cover Base - Remove and Install".
Remove the speed/timing sensor. Refer to the Service Manual, "Electronic Troubleshooting" module.
Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic Control Module (ECM) and Personality Module (PM) - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01007161
Remove tube assemblies (1).
Remove bolts (3) and covers (2) from both sides of the engine.
Illustration 2 g00914348
Remove covers (4) from both sides of the front housing.
Illustration 3 g01053356
Pull valve lifters (5) away from the camshaft. Hold valve lifters (5) in position with O-ring seals.
Illustration 4 g01053366
Remove covers (6) for the camshaft drive gears from the flywheel housing.
Illustration 5 g01053357
Remove the bolt and plate (7) that fastens camshaft drive gear (8) to the camshaft.
Illustration 6 g00914453
Place the three washers from Tooling (B) behind plate (7) and install the bolt.
Do not apply more than 51675 kPa (7500 psi) pressure to the hydraulic puller. The adapters are rated at 6 1/2 tons each and the hydraulic puller is rated at 17 tons at 68900 kPa (10000 psi). If too much pressure is applied, the gear may be damaged.
Install Tooling (B) on camshaft drive gear (8). Apply 51675 kPa (7500 psi) to Tooling (B). Strike the screw on Tooling (B) with a hammer until camshaft drive gear (8) is free from the camshaft. Remove Tooling (B) and camshaft drive gear (8).
Illustration 7 g00613686
Remove bolts (9) and thrust washers (10) that fasten the camshaft to the engine block.
Perform Steps 5 through 9 for the camshaft on the other side of the engine.
Illustration 8 g00914454
Remove timing ring (11) from the camshaft.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 238-9586 Camshaft Drive Group 1
B 1P-0820 Hydraulic Puller 1
8B-7548 Push-Puller Tool Group 1
8B-7559 Adapter 2
5H-1504 Hard Washer 3
9U-6600 Hand Hydraulic Pump 1
C 125-0200 Camshaft Pilot As 2
D 125-0201 Camshaft Guide As 1
E 8T-3169 Crank Assembly 1 Start By:
Remove the valve cover base. Refer to Disassembly and Assembly, "Valve Cover Base - Remove and Install".
Remove the speed/timing sensor. Refer to the Service Manual, "Electronic Troubleshooting" module.
Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic Control Module (ECM) and Personality Module (PM) - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01007161
Remove tube assemblies (1).
Remove bolts (3) and covers (2) from both sides of the engine.
Illustration 2 g00914348
Remove covers (4) from both sides of the front housing.
Illustration 3 g01053356
Pull valve lifters (5) away from the camshaft. Hold valve lifters (5) in position with O-ring seals.
Illustration 4 g01053366
Remove covers (6) for the camshaft drive gears from the flywheel housing.
Illustration 5 g01053357
Remove the bolt and plate (7) that fastens camshaft drive gear (8) to the camshaft.
Illustration 6 g00914453
Place the three washers from Tooling (B) behind plate (7) and install the bolt.
Do not apply more than 51675 kPa (7500 psi) pressure to the hydraulic puller. The adapters are rated at 6 1/2 tons each and the hydraulic puller is rated at 17 tons at 68900 kPa (10000 psi). If too much pressure is applied, the gear may be damaged.
Install Tooling (B) on camshaft drive gear (8). Apply 51675 kPa (7500 psi) to Tooling (B). Strike the screw on Tooling (B) with a hammer until camshaft drive gear (8) is free from the camshaft. Remove Tooling (B) and camshaft drive gear (8).
Illustration 7 g00613686
Remove bolts (9) and thrust washers (10) that fasten the camshaft to the engine block.
Perform Steps 5 through 9 for the camshaft on the other side of the engine.
Illustration 8 g00914454
Remove timing ring (11) from the camshaft.
Caterpillar parts catalog:
Parts fork Caterpillar catalog:
120B, 12E, 140, 140B
120B, 12E, 140, 140B
120B, 12E, 140, 140B
12E
8D0779
FORK
140, 140B, 14E
140, 140B, 14E
120, 120B
120B, 12E, 140B
120B, 12E, 140B
120B, 140B
2F5974
FORK
12E
12E
4D8411
FORK
16
16
8D0756
FORK
16
16
120, 120B
8D0779
FORK
140, 140B, 14E
140, 140B, 14E
140
4D8007
FORK
16
16
2F5974
FORK
12E
12E
120B, 140B
120B, 12E, 140B
120B, 12E, 140B