AVSPARE.COM
parts catalog

FRAME AS 2444117 - Caterpillar


2444117 FRAME AS Caterpillar parts PM-201
Rating:
81
Alternative (cross code) number:
CA2444117
244-4117
2444117
Caterpillar 2444117 FRAME AS

Buy FRAME AS 2444117 Caterpillar genuine, new aftermarket tractor parts with delivery
COLD PLANER,

Compatible equipment models: 2444117:

COLD PLANER  PM-201   Caterpillar
Number on catalog scheme: 8
 
  For full view, you need register

Information:


Illustration 1 g02339637
Connections for the Boom Angle sensor This diagnostic code is associated with the Boom Angle sensor. An FMI 03 diagnostic code indicates the Machine ECM has determined the sensor circuit voltage is above normal.For machines equipped with the E-Fence feature, reference Troubleshooting, " E-Ceiling and Cab Avoidance - Troubleshoot"Possible causes for this diagnostic code are listed below:
Sensor power supply failure.
The sensor has failed.
Open sensor output circuit.
Sensor output shorted to power supply.
The Machine ECM has failed (unlikely).Note: Poor connections are often the cause of a problem in electrical circuits. Before performing this procedure, inspect all the machine harnesses and connectors involved in the circuit. Make sure to verify that all of the connections in the circuit are clean, secure, and in good condition. Correct any problems found with any of the connections. Verify the diagnostic code CID 2425 FMI 03 is still active, before continuing with this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes now, but clear those diagnostic codes when the original diagnostic code has been corrected. Test Step 1. CHECK THE SENSOR POWER SUPPLY.
The key start switch and the disconnect switch remain in the ON position.
At the machine harness connector for the Boom Angle sensor, measure the voltage between the contact for A (wire R997-OR) and the contact for B (wire A209-BK) in the sensor harness connector.Expected Result:The voltage is 5 VDC.Results:
YES - The voltage is 5 VDC. Go to Test Step 2.
NO - The voltage is not 5 VDC. Repair: There is a problem with the 5 VDC power supply from the Machine ECM. Use the procedures found in the MID 039 CID 0262 FMI 06 diagnostic code document in this publication to troubleshoot this power supply problem. After the 5 VDC power supply problem is corrected, check if the CID 2425 FMI 03 diagnostic code is active. If the diagnostic code is active, go to Test Step 2.Test Step 2. CHECK THE SENSOR.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness connector from the Boom Angle sensor.
At the sensor harness connector, insert a jumper wire between the contact for C (wire E441-GN) and the contact for B (wire A209-BK) in the sensor harness connector.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the CID 2425 FMI 03 diagnostic code. Expected Result:The CID 2425 FMI 03 diagnostic code stays active. Results:
YES - The CID 2425 FMI 03 diagnostic code stays active. The sensor is not the cause of the problem. Go to Test Step 3.
NO - The CID 2425 FMI 03 diagnostic code is no longer active and has been replaced by a CID 2425 FMI 04 diagnostic code.Repair: The sensor has failed. Replace the sensor. The new sensor will need to be calibrated. Go to Test Step 5.Test Step 3. CHECK THE SENSOR CIRCUIT FOR AN OPEN.
Turn the key start switch and the disconnect switch to the OFF position.
The sensor harness connector

Caterpillar parts catalog:

Caterpillar parts catalog
PM-201 Cold Planer PNM00001-UP (MACHINE) POWERED BY C18 Engine


Parts frame Caterpillar catalog:

3T3418 FRAME AS-END
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H NA, 16M, 2290, 235, 235D, 2390, 2391, 245, 2491...
2289656 FRAME AS-DRIVE END
120M, 12M, 140H, 143H, 14H, 14M, 160H, 163H, 16H, 2384C, 2470C, 2484C, 2570C, 2670C, 2864C, 320D GC, 320D L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323E L, 324E, 324E L, 324E LN, 329E, 329E...
2289655 FRAME AS-ALTERNATOR
120M, 12M, 140H, 143H, 14H, 14M, 160H, 163H, 16H, 2384C, 2470C, 2484C, 2570C, 2670C, 2864C, 320D GC, 320D L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323E L, 324E, 324E L, 324E LN, 329E, 329E...
0774901 FRAME
PM-201, PM-465, PM-565, PM-565B, PR-1000, PR-450, PR-450C
1782654 FRAME AS
PM-201, PM-565B
2334865 FRAME
PM-201, PM-565B
2334868 FRAME
PM-201, PM-565B
1782654 FRAME AS
PM-201, PM-565B
2334865 FRAME
PM-201, PM-565B
2334868 FRAME
PM-201, PM-565B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.