FRAME GP-LOADER 2935309 - Caterpillar

2935309 FRAME GP-LOADER Caterpillar parts 416E, 420E, 430E

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2935309
293-5309
2935309

Buy FRAME GP-LOADER 2935309 Caterpillar genuine, new aftermarket tractor parts with delivery
BACKHOE LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Aries 2935309 StyleGuard Black Floor Liner Set

$141.05

28 Jul 2017

ARIES: ARIES

Aries 2935309 StyleGuard Black Floor Liner Set
Durable, textured surface for a refined appearance and ultimate interior protection||Triple-layer construction using industrial-strength materials||Thousands of patented OmniGrip fibers resist slipping on all types of carpet||Laser-measured for perfect, vehicle-specific contour||Limited lifetime warranty

Number on catalog scheme:

Caterpillar 2935309 Parts scheme FRAME GP-LOADER

For full view, you need register

Compatible equipment models: 2935309:

BACKHOE LOADER 416E 420E 430E Caterpillar

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 367-8608 Engine Timing Pin 1
C 298-5564 T40 Torx Socket 1
D 227-4389 E10 Torx Socket 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure. Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01992076
Remove plug (2) from the cylinder block. Remove O-ring seal (1) from the plug.
Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Position the Valve Mechanism Before Maintenance Procedures" for the correct procedure. Install Tooling (B) through Hole (W) in order to lock the crankshaft.
Remove Tooling (B).
Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the crankshaft at 60 degrees after top dead center.
Illustration 2 g01992077
Use Tooling (C) in order to loosen threaded inserts (4) on all rocker arms (3). Unscrew threaded inserts (4) on all rocker arms (3) until all valves are fully closed. Ensure that guides (5) for the pushrods are left in position on threaded inserts (4). Note: Ensure that ALL threaded inserts are fully unscrewed.
Illustration 3 g02003036
Illustration 4 g02003035
Use Tooling (D) to loosen Torx screws (7). Begin at the ends of rocker shaft assembly (2) and work toward the center. Note: To avoid distortion of the rocker shaft assembly, each Torx screw should be loosened by half a turn at one time. Repeat the procedure until all Torx screws are loosened.
Remove Torx screws (7) from rocker shaft assembly (8). Note: Note Position (X) of different length Torx screws (7).
Remove rocker shaft assembly (8) from the cylinder head.
Place an identification mark on pushrods (9) in order to show the location. Remove the pushrods from the cylinder head. Note: Identification will ensure that the pushrods can be reinstalled in the original positions. Do not interchange the positions of used pushrods.
Make a temporary mark on valve bridges (6) in order to show the location and the orientation. Remove the valve bridges from the cylinder head. Note: Identification will ensure that the valve bridges can be reinstalled in the original location and the original orientation. Do not interchange the location or the orientation of used valve bridges.