3270107 FRAME GP-LOADER Caterpillar parts
428E
Rating:
Alternative (cross code) number:
CA3270107
327-0107
3270107
CA3270107
327-0107
3270107
BACKHOE LOADER,
Compatible equipment models: 3270107:
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 6V-8197 Forcing Screw (M12 by 1.75 by 40 mm) 2 Start By:
Remove the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Remove".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Drain the oil from the swing drive. The capacity of the swing drive is approximately 1.5 L (0.4 US gal). Refer to Operation and Maintenance Manual, SEBU7613, "Swing Drive Oil - Change" for the correct procedure for draining the swing drive.
Illustration 1 g00907900
Remove bolts (1) that hold the swing drive to the undercarriage frame. Use bolts (1) to attach Tooling (A) to swing drive (2) .
Use a suitable lifting device to remove the swing drive. The weight of the swing drive is approximately 57 kg (125 lb).
Illustration 2 g00907920
Install Tooling (B) in each threaded hole in the swing drive housing. Tighten the forcing screws evenly in order to separate swing drive (2) from the dowels and the undercarriage frame.
Remove swing drive (2) from the machine.
Place the swing drive on wood blocks in order to prevent damage to the drive gear.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 6V-8197 Forcing Screw (M12 by 1.75 by 40 mm) 2 Start By:
Remove the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Remove".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Drain the oil from the swing drive. The capacity of the swing drive is approximately 1.5 L (0.4 US gal). Refer to Operation and Maintenance Manual, SEBU7613, "Swing Drive Oil - Change" for the correct procedure for draining the swing drive.
Illustration 1 g00907900
Remove bolts (1) that hold the swing drive to the undercarriage frame. Use bolts (1) to attach Tooling (A) to swing drive (2) .
Use a suitable lifting device to remove the swing drive. The weight of the swing drive is approximately 57 kg (125 lb).
Illustration 2 g00907920
Install Tooling (B) in each threaded hole in the swing drive housing. Tighten the forcing screws evenly in order to separate swing drive (2) from the dowels and the undercarriage frame.
Remove swing drive (2) from the machine.
Place the swing drive on wood blocks in order to prevent damage to the drive gear.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts frame Caterpillar catalog:
2096865
FRAME GP-SWING
422E, 428E, 432E, 434E
422E, 428E, 432E, 434E
2127458
FRAME GP-SLIDING
422E, 428E, 432E, 434E, 442E, 444E
422E, 428E, 432E, 434E, 442E, 444E
2470793
FRAME GP-SLIDING
422E, 428E, 432E, 434E, 442E, 444E
422E, 428E, 432E, 434E, 442E, 444E
416E, 420E, 422E, 428E, 432E, 434E
414E, 416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, D3K XL, D4K XL, D5K LGP
422E, 428E, 432E, 434E, 442E, 444E
3151277
FRAME AS
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3065295
FRAME AS
428E
428E
3041904
FRAME GP-TRACK ROLLER
279C, 289C, 299C
279C, 289C, 299C
3041903
FRAME GP-TRACK ROLLER
279C, 289C, 299C
279C, 289C, 299C
3101340
FRAME GP-FRONT
120M 2
120M 2
3205328
FRAME GP
789D
789D
3257603
FRAME GP-LOADER
432E, 442E
432E, 442E